EDGE 4416155 - Caterpillar

Coat all bores for pins with lubricant.(1) 7Y2348 Pin: Diameter after plating ... 79.85 0.04 mm (3.143 .002 in)Plating thickness ... 0.013 mm (.0005 in) minimum(2) 7Y2349 Pin: Diameter after plating ... 69.85 0.04 mm (2.750 .002 in)Plating thickness ... 0.013 mm (.0005 in) minimum(3) 7Y2357 Pin (two places): Diameter after plating ... 79.85 0.04 mm (3.143 .002 in)Plating thickness ... 0.013 mm (.0005 in) minimum(4) (5) Nuts: Position nut (4) 0.5 mm (.02 in) in from the end of the bolt. Tighten nut (5) against nut (4) (four places) to a torque of ... 200 40 N m (150 30 lb ft)(6) Lubricate sealing lips lightly with lubricant being sealed. Six places.(7) When assembling the linkage group on the machine, rotate the rod end of the bucket cylinder to position the grease fitting away from the stick.(8) 7Y5128 Bearing: Outside diameter ... 95.180 0.013 mm (3.7472 .0005 in)Inside diameter ... 80.25 0.02 mm (3.159 .001 in)Install bearing in bore (two places) ... 7.0 0.3 mm (.28 .01 in)(9) 7Y3428 Bearing: Outside diameter ... 95.180 0.013 mm (3.7472 .0005 in)Inside diameter ... 80.25 0.02 mm (3.159 .001 in)Install bearing in bore (two places) ... 5.0 0.3 mm (.20 .01 in)7Y2216 (D-Family)
Coat all bores for pins with lubricant.(1) 7Y3547 Pin: Diameter after plating ... 89.85 0.04 mm (3.357 .002 in)Plating thickness ... 0.013 mm (.0005 in) minimum(2) 7Y3548 Pin: Diameter after plating ... 69.85 0.04 mm (2.750 .002 in)Plating thickness ... 0.013 mm (.0005 in) minimum(3) 7Y3550 Pin: Diameter after plating ... 89.85 0.04 mm (3.357 .002 in)Plating thickness ... 0.013 mm (.0005 in) minimum(4) (5) Nuts: Position nut (4) 0.5 mm (.02 in) in from the end of the bolt. Tighten nut (5) against nut (4) (four places) to a torque of ... 200 40 N m (150 30 lb ft)(6) Lubricate sealing lips lightly with lubricant being sealed. Four places.(7) Lubricate sealing lips lightly with lubricant being sealed. Two places.(8) When assembling the linkage group on the machine, rotate the rod end of the bucket cylinder to position the grease fitting away from the stick.(9) 7Y3552 Bearing: Outside diameter ... 106.200 0.013 mm (4.1810 .0005 in)Inside diameter ... 90.27 0.02 mm (3.554 .001 in)Install bearing in bore (two places) ... 9.0 0.3 mm (.35 .01 in)(10) 7Y3428 Bearing: Outside diameter ... 95.180 0.013 mm (3.7472 0005 in)Inside diameter ... 80.25 0.02 mm (3.159 .001 in)Install bearing in bore (two places) ... 5.0 0.3 mm (.20 .01 in)(11) 7Y3549 Pin: Diameter after plating ... 79.85 0.04 mm (3.144 .002 in)Plating thickness ... 0.013 mm (.0005 in) minimum7Y9020