AVSPARE.COM
parts catalog

ELBOW-EXH 1C4193 - Caterpillar



1C4193 ELBOW-EXH Caterpillar parts ELBOW
Rating:
16
Alternative (cross code) number:
CA1C4193
1C-4193
1C4193
Caterpillar 1C4193 ELBOW-EXH
Weight: 24 pounds 11 kg.

Buy ELBOW-EXH 1C4193 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Start By:a. remove differentials and pinion assemblies. Fluid Spillage ContainmentCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. The disassembly procedure is the same for the front and rear pinion assemblies. 1. Remove six bolts (1) and the washers that hold retainer (2) to the pinion housing. Remove the retainer. 2. Remove lip-type seal (3) from retainer (2). 3. Bend crimp (4) away from the slot in the pinion shaft with a hammer and punch.4. Use Tool (A) to remove nut (5) from the pinion shaft. 5. Using a press, remove pinion shaft (6) from the pinion housing. 6. Remove bearing cones (8) and bearing cups (7) from the pinion housing.Assemble Pinion Assemblies (928G & IT28G)
The same assembly is used for both the front and rear pinon assemblies. Fluid Spillage ContainmentCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. Cup freezing or cone heating may be used if cups or cones are reset with a driver or press after parts have reached a uniform temperature. Limit cone heating to 135°C (275°F) maximum for a maximum of 4 hours. Lubricate bearings after they have cooled to prevent rusting.1. Install bearing cups (8) and (10) in pinion housing (9). The bearing cups must be seated against the shoulders in pinion housing (9).2. Install bearing cone (7) on pinion (6). Bearing cone (7) must be against (seated) the shoulder on pinion (6). Lubricate bearing cone (7).3. Install pinion (6) in housing (9). Press bearing cone (11) into place leaving a small amount of end play. Lubricate bearing cone (11). Lubricate and install the washer and nut (5).4. Position the assembly vertically in a soft jawed vise. Tighten the vise against the teeth on pinion shaft (6). Install an appropriate size bolt and nut through an outer mounting bolt hole in pinion housing (9).5. Place a 203 mm (8.0 in) torque wrench on this bolt so that it is in line with the center of pinion shaft (6).6. While turning pinion housing (9) with the torque wrench, tighten nut (5) until the torque wrench reading in the following chart is reached.
*When using a 203 mm (8.0 in) torque wrench.Check to be sure that there is zero end play of pinion shaft (6).7. If pinion rolling torque exceeds the specification, back


Parts elbow Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.