AVSPARE.COM
parts catalog

ELECTRONICS GP-POWER TRAIN 3534365 - Caterpillar



3534365 ELECTRONICS GP-POWER TRAIN Caterpillar parts 120M 2, 12M 2, 140M 2, 160M 2 ELECTRONICS
Rating:
60
Alternative (cross code) number:
CA3534365
353-4365
3534365
Caterpillar 3534365 ELECTRONICS GP-POWER TRAIN

Buy ELECTRONICS GP-POWER TRAIN 3534365 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER,

Compatible equipment models: 3534365:

MOTOR GRADER  120M 2   12M 2   140M 2   160M 2   Caterpillar
Number on catalog scheme: 11
 
  For full view, you need register

Information:


If the flash file and engine application are not matched, engine damage may result.
Perform the following procedure in order to replace the ECM:
Record the configuration data:
Try to establish communication between the Caterpillar Electronic Technician (ET) and the ECM. Proceed to Test Step 2 if Cat ET does not communicate with the ECM.
Print the parameters from the "Configuration" screen on Cat ET. If a printer is unavailable, record all of the parameters.
Obtain the customer passwords from the vehicle owner. Access the customer specified parameters with Cat ET. Record the value of each customer parameter.
Record ECM lifetime totals.________
Record any logged diagnostic codes. ________Note: If the customer passwords are not available proceed to Troubleshooting, "Customer Passwords" for details that are related to customer passwords.
Use the "Copy Configuration/ECM Replacement" feature that is found under the "Service" menu on Cat ET. Select "Load from ECM" in order to copy the configuration data from the suspect ECM. Note: If the "Copy Configuration" process fails and the parameters are not obtained in Step 1.b, the parameters must be obtained elsewhere. Some of the system configuration parameters are stamped on the engine information plate. Most of the parameters must be obtained from the factory. Parameters that are related to customer specified parameters must be obtained from the customer or from the Original Equipment Manufacturer (OEM).
Remove the ECM:
Turn the keyswitch OFF.
Disconnect the P1 and P2 connectors.
Disconnect the ECM ground strap.
Remove the mounting hardware at each corner of the ECM.
Install the replacement ECM:
Use the old mounting hardware to install the replacement ECM.
Connect the ECM ground strap.
Connect the P1 and P2 connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Configure the replacement ECM:
Flash program the latest available flash file into the ECM. Refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
Use Cat ET to match the engine application and the interlock code if the replacement ECM was used for a different application.
If the "Copy Configuration" process from Step 1.b was successful, return to the "Copy Configuration/ECM Replacement" screen on Cat ET and select "Program ECM". Proceed to Step 4.e when programming is complete.
If the "Copy Configuration" process from Step 1.b was unsuccessful, manually program the ECM parameters. The parameters must match the parameters from Step 1.b.
Program the engine monitoring system, if necessary.
Calibrate the engine speed/timing if there is a diagnostic code for speed/timing sensor calibration. The procedure is in Troubleshooting, "Timing - Calibrate". Note: If an engine is a Series C7.1 or Series C9.3, use Cat ET to perform the "fuel system functional test". This test established a baseline value of the fuel system rate of fuel return at high rail pressure. Other diagnostic codes may be activated if this test is not performed.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
160M Series 2 MOTOR GRADER R9L00001-UP (MACHINE) POWERED BY C9 ENGINE
12M Series 2 Motor Grader R9S00001-UP (MACHINE) POWERED BY C9.3 Engine
140M Series 2 Motor Grader R9M00001-UP (MACHINE) POWERED BY C9 Engine
120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWERED BY C7.1 Engine
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWERED BY C9 Engine
160M Series 2 MOTOR GRADER R9T00001-UP (MACHINE)
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engine
140M Series 2 Motor Grader - All Wheel Drive M9J00001-UP (MACHINE) POWERED BY C9.3 Engine
160M Series 2 Motor Grader - All Wheel Drive M9K00001-UP (MACHINE) POWERED BY C9.3 Engine
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWERED BY C7.1 Engine
160M Series 2 Motor Grader M9E00001-UP (MACHINE) POWERED BY C9 Engine
120M Series 2 Motor Grader M9C00001-UP (MACHINE) POWERED BY C7.1 Engine
120M Series 2 Motor Grader R9N00001-UP (MACHINE) POWERED BY C7.1 Engine
12M Series 2 Motor Grader - All Wheel Drive R9P00001-UP (MACHINE) POWERED BY C9.3 Engine
12M Series 2 Motor Grader - All Wheel Drive F9B00001-UP (MACHINE) POWERED BY C9.3 Engine
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
120M Series 2 OEM Motor Grader M9200001-UP (MACHINE) POWERED BY C7.1 Engine


Parts electronics Caterpillar catalog:

2456573 ELECTRONICS GP-MACHINE
AP-1055D, BG-2455D, BG-260D
3566068 ELECTRONICS GP-MACHINE
272D, 272D XHP, 299D, 299D XHP
1646901 ELECTRONICS GP-POWER TRAIN
69D, 769D, 771D, 773D, 775D, 776D, 777D, 784C, 785C, 789C, 793C
1927136 ELECTRONICS GP-MONITOR
785C, 785D, 789C, 789D, 793C, 793D
3398912 ELECTRONICS GP-MONITOR
793F, 793F OEM, 793F-XQ, 797F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.