parts catalog

ENGINE AR 1246304 - Caterpillar

1246304 ENGINE AR Caterpillar parts 3116 ENGINE
Alternative (cross code) number:
Caterpillar 1246304 ENGINE AR

Buy ENGINE AR 1246304 Caterpillar genuine, new aftermarket tractor parts with delivery

Related part:
1246304  SHORT BLOCK  0R9294  R

Compatible equipment models: 1246304:

TRUCK ENGINE  3116   Caterpillar
  For full view, you need register


Illustration 21 g06067010
Illustration 22 g06067154
Illustration 23 g06067209
Illustration 24 g06067216
Illustration 25 g06067233
Illustration 26 g06067317Film Installation
Avoid prolonged skin contact with isopropyl alcohol. Avoid breathing the vapors in enclosed areas without adequate ventilation and do not smoke.Isopropyl alcohol is flammable. Do not use near open flame, welding operations, or around heated surfaces exceeding 482°C (900°F).
Surface preparation is important in the installation of films. The surface must be clean and dry in order for the films to adhere to the machine. Be sure that oil, grease, and dirt have been removed before you install the new films. The installation instructions that follow are recommended:
A 50:50 mixture of isopropyl alcohol and water is generally an adequate cleaning agent for cleaning the mounting surface.
Apply solvent to the contact area. Wipe the surface with a lint free cloth until the surface is dry.
Carefully remove the liner from the back of the film. Avoid touching the adhesive.
Illustration 27 g06065738
Typical example
Apply the film to the surface underneath the existing film that contains the machine model number on both sides of machine. Ensure that the upper corner of the film intersects the edge of the plate shown in Illustration 27.Note: The film cannot be repositioned once the film is applied. If the film is installed incorrectly, the film must be removed and discarded. Start again and use a new film.
Press the film firmly into place. Apply pressure evenly across the entire surface of the film. The use of a hand roller or a squeegee is recommended to ensure maximum adhesion to the mating surface. Remove any bubbles that remain under the film.Software Installation
Ensure that the 460-5343 Joystick Control Group (Right-Hand Joystick), is already installed on the machine. If changing the control group is necessary, refer to Special Instruction, REHS8704 for installation instructions.The 421-0263 High Flow Kit must be configured using Cat® Electronic Technician (Cat ET) Service Tool.Machine Configuration
With the key in the on position and engine off, use Cat ET to select the machine ECM.
Illustration 28 g06066075
From the menu, select "Service", "Configuration", and then "Implement Configuration".
Illustration 29 g06066081
In the configuration screen, double-click on the "Auxiliary Hydraulic High Flow System Installation Status" link.
Illustration 30 g06066085
In the pop-up window, change the "New Value" field to "Installed" and click "OK".
Turn the start key to the off position and wait at least 15 seconds. Then, turn the start key back to the on position.Note: The new feature will be activated on the next power cycle.
From the Cat ET menu, select "Service", then "Configuration", and then "Implement Configuration".
Illustration 31 g06067325
In the configuration screen, double-click on the "Auxiliary Hydraulic High Flow System Installation Status" link. Ensure that the feature is set to "Installed".

Caterpillar SIS machinery equipment:

Caterpillar SIS

Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.