AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1246722 - Caterpillar



1246722 ENGINE AR-COMPLETE Caterpillar parts 3406C ENGINE
Rating:
34
Alternative (cross code) number:
CA1246722
124-6722
1246722
Caterpillar 1246722 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1246722 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1246722:

TRUCK ENGINE  3406C   Caterpillar
  For full view, you need register

Information:

2. Loosen two clamps (1).3. Slide air inlet hose (2) away from turbocharger (3).4. Loosen hose clamp (6).5. Disconnect hose (5).6. Loosen clamp (4). Pull tube assembly away from turbocharger (3).7. Remove the two bolts holding oil tube (7) to turbocharger (3).8. Disconnect connector (10).9. Remove two bolts (8).10. Remove oil tube (9) and gasket. Check gasket for wear or damage. Replace if necessary.11. Remove four nuts (11). When installing, apply 5P3931 Anti-Seize Compound to the studs. Tighten nuts (11) to a torque of 54 5 N m (40 4 lb ft).12. Remove turbocharger (4) and gasket. Check gasket for wear or damage. Replace if necessary.13. Remove oil tube (7). Check gasket and seal for wear or damage. Replace if necessary. For installation of the turbocharger, reverse the removal steps.Disassemble & Assemble Turbocharger
Start By:a. remove turbocharger Mark housings orientation before beginning disassembly procedure. 1. Remove bolts (1) and (2). Remove the compressor and turbine housing. 2. Remove nut (3) and compressor wheel (4). Slide turbine wheel (5) and the shaft out. Remove the piston ring from the shaft. 3. Remove adapter plate snap ring (6).4. Using two screwdrivers, remove adapter plate (7). 5. Remove the flinger sleeve, bearing (8), spacers (9) and seals (10). 6. Remove snap ring (11), bushing (12) and the other snap ring. 7. Remove snap ring (13), bushing (14) and the other snap ring. The following steps are for the assembly of the turbocharger.8. Be sure all parts of the turbocharger are thoroughly clean and free of dirt and debris.9. Install bushing (12) and snap ring (11). Repeat this procedure for bushing (14) and snap ring (13). Install the piston ring on the turbine wheel end of the shaft. 10. With the seals and shield (15) in place, install shaft and turbine wheel assembly (5). Bearing (8) locates on the pin in the bearing housing assembly.11. Install the spacers, bearing, plate, seals and adapter plate. Install the snap ring (not shown).
Do not allow any of the 9S3263 Thread Lock to get on the shaft. Damage to the turbocharger may occur.
12. Install compressor wheel (4) on the shaft. Put one drop of 9S3263 Thread Lock on the threads, and install nut (3). Tighten nut (3) to a torque of 10.2 .6 N m (90 5 lb in). Make sure the housings orientation marked before disassembly procedure are correctly positioned for assembly.13. Position the turbine and compressor housings. Put 5P3931 Anti-Seize Compound on the bolts, and install them. Tighten bolts (1) for the compressor cover to a torque of 7.3 .6 N m (65 5 lb in). Tighten bolts (2) of the turbine housing to a torque of 15.8 .6 N m (140 5 lb ft).End By:a. install turbocharger

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.