1695067 ENGINE AR-COMPLETE Caterpillar parts C-10 ENGINE
Rating:
Alternative (cross code) number:
CA1695067
169-5067
1695067
CA1695067
169-5067
1695067
TRUCK ENGINE,
Compatible equipment models: 1695067:
TRUCK ENGINE C-10
Caterpillar
For full view, you need register
Information:
Removal Procedure
Start By:
Release the system pressure.
Remove the wheels and tires.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Drain the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
Illustration 1 g06238063
Cut cable strap (2) and disconnect harness assembly (1).
Disconnect hose assemblies (3) and (5).
Remove two fittings (4).
Illustration 2 g06237645
Remove four bolts (6). Do not remove all five bolts.
Illustration 3 g06237649
Remove four bolts (7). Do not remove all five bolts.
Illustration 4 g06237656
Attach a suitable lifting device to piston motor (propel) (rear) (9). The weight of piston motor (propel) (rear) (9) is approximately 95 kg (209 lb).
Remove bolts (8) and position piston motor (propel) (rear) (9) as shown in Illustration 4.
Illustration 5 g06237657
Attach a second suitable lifting device to piston motor (propel) (rear) (9). The weight of piston motor (propel) (rear) (9) is approximately 95 kg (209 lb). Remove piston motor (propel) (rear) (9).Installation Procedure
Install piston motor (propel) (rear) (9) in the reverse order of removal.
Start By:
Release the system pressure.
Remove the wheels and tires.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Drain the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
Illustration 1 g06238063
Cut cable strap (2) and disconnect harness assembly (1).
Disconnect hose assemblies (3) and (5).
Remove two fittings (4).
Illustration 2 g06237645
Remove four bolts (6). Do not remove all five bolts.
Illustration 3 g06237649
Remove four bolts (7). Do not remove all five bolts.
Illustration 4 g06237656
Attach a suitable lifting device to piston motor (propel) (rear) (9). The weight of piston motor (propel) (rear) (9) is approximately 95 kg (209 lb).
Remove bolts (8) and position piston motor (propel) (rear) (9) as shown in Illustration 4.
Illustration 5 g06237657
Attach a second suitable lifting device to piston motor (propel) (rear) (9). The weight of piston motor (propel) (rear) (9) is approximately 95 kg (209 lb). Remove piston motor (propel) (rear) (9).Installation Procedure
Install piston motor (propel) (rear) (9) in the reverse order of removal.
Caterpillar SIS machinery equipment:
Caterpillar SIS
- C-10 Truck Engine 8YS00001-UP » 169-5067 ENGINE AR-COMPLETE