parts catalog

ENGINE AR-COMP 1695121 - Caterpillar

1695121 ENGINE AR-COMP Caterpillar parts ENGINE
Alternative (cross code) number:
Caterpillar 1695121 ENGINE AR-COMP

Buy ENGINE AR-COMP 1695121 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
The ROP Shop Genuine OEM PTO Switch fits Simplicity 1695117 1695118 1695119 1695120 1695121

09 Aug 2021

US: The ROP Shop
The ROP Shop Genuine OEM PTO Switch fits Simplicity 1695117 1695118 1695119 1695120 1695121
The ROP Shop New Genuine OEM PTO SWITCH || Fits Simplicity 1695117 1695118 1695119 1695120 1695121 || No. of Positions - 2, No. of Terminals - 2 || Push/Pull Yellow Knob, Snap Mount || Quality Aftermarket Part with 1 Year Warranty
  For full view, you need register


Stopping the engine immediately after it has been working under load can result in overheating and accelerated wear of engine components.Refer to the following procedure to allow the engine to cool and to prevent excessive temperatures in the turbocharger housing, which could cause oil coking problems.
Stop the machine and run the engine at low idle for 5 minutes.
Never turn the battery disconnect switch to the OFF position while the engine is running. Serious damage to the electrical system may result.
Illustration 1 g02038994
Turn the engine start switch to the OFF position and remove the engine start switch key. Engine Stop Control
Turn the engine start switch to the OFF position. If the engine does not stop, perform the following procedure.
Illustration 2 g00837903
The switch is located below the cab on the left side of the machine.
Illustration 3 g03374841
Lift cover (1).
Push switch (2) upward. This should stop the engine. Note: Use the engine start switch to stop the engine first. Use the engine stop control as an alternate method to stop the engine.
Return the switch to the original position. The engine will be enabled to start. Note: Do not operate the machine again until the malfunction has been corrected.
Use the method that follows if the previous steps do not stop the engine. Stop the Engine if an Electrical Malfunction Occurs
Turn the engine start switch to the OFF position. If the engine does not stop, perform the procedure that follows.
Illustration 4 g01139594
The fuel shutoff valve is located under the fuel tank.
Shut off the fuel supply by turning the fuel shutoff valve clockwise. The engine will stop after consuming the fuel in the fuel line. The engine may continue to run for a few minutes.Repair the engine before you restart the engine. The fuel system may need to be primed. See Operation and Maintenance Manual, "Fuel System - Prime" for instructions.Delayed Engine Shutdown
Illustration 5 g03889643
(1) Delayed Engine Shutdown Override The Delayed Engine Shutdown allows the engine to run for a time after the engine start switch key is turned to the OFF position to cool the engine and system components. The engine start switch key may be removed.Note: The DEF purge process will run for 2 minutes once the engine is shut down and must complete. The purge process may occur during delayed engine shutdown. Do not turn off battery disconnect switch during the purge process. Do not turn off the battery power disconnect switch until the battery disconnect switch indicator lamp has turned off. If the purge process does not complete, a diagnostic code will become active.Note: There may be regulations that define the requirements for the operator and/or support personnel to be present when the engine is running.
Leaving the machine unattended when the engine is running may result in personal injury or death. Before leaving the machine operator station, neutralize the travel controls, lower the work tools to the ground and deactivate all work tools, and place the lever for the hydraulic lockout control in the LOCKED position.
Note: Leaving the engine unattended while running may result in

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.