AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1695169 - Caterpillar



1695169 ENGINE AR-COMPLETE Caterpillar parts C-12 ENGINE
Rating:
70
Alternative (cross code) number:
CA1695169
169-5169
1695169
Caterpillar 1695169 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1695169 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
New Genuine Simplicity RUBBER HOOD STRAP fits Catcher 1694916 1694918 1695169 by The ROP Shop
$11.99
 

31 Jul 2018
6 Hundredths Pounds
The ROP Shop: The ROP Shop
New Genuine Simplicity RUBBER HOOD STRAP fits Catcher 1694916 1694918 1695169 by The ROP Shop
New Genuine Simplicity RUBBER HOOD STRAP || Fits Catcher 1694916 1694918 1695169 || Replaces OEM Simplicity 2171600SM 2171600 171600 72028479 || Fast & Free Shipping from The ROP Shop || Quality Aftermarket Part with 1 Year Warranty
  For full view, you need register

Compatible equipment models: 1695169:

TRUCK ENGINE  C-12   Caterpillar

Information:

Important Safety Information
Do not perform any procedures in this Troubleshooting Guide until you have read the Operation and Maintenance Manual and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. Follow the procedures below.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Safety precautions and warnings are provided in this publication and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard.Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive.Overview
These engines are equipped with an electronic control system. The system consists of a computer, sensors, and software. The system performs these functions:
Control of the engine
Control of particulate emissions via the Clean Emission Module (CEM)
Applications control system interface
Fault detection and reportingElectronic Control System
The Electronic Control Module (ECM) is a computer that controls the operation of the engine.The ECM contains a flash file. The flash file is the software for the ECM. The flash file contains the operating maps. The operating maps define the following characteristics of the engine:
Horsepower
Torque curves
Engine speed (rpm)Refer to Troubleshooting, "System Overview" for additional information on the electronic control system.Application Interface
The ECM interfaces with the machine via software and an electrical connector on the ECM. The software can be configured.The application control system provides inputs to the electrical connector on the ECM to indicate the status of switches. Correctly configure the ECM to interpret the inputs.The ECM provides outputs for the application control system via the electrical connector to control lamps, solenoids, and other devices. Correctly configure the ECM in order for the outputs to match the configuration of the application control system.Clean Emissions Module (CEM)
The CEM contains these components:Diesel Particulate Filter (DPF) - A DPF is installed in the exhaust system. The DPF collects soot and ash from the engine exhaust.Diesel Oxidation Catalyst (DOC) - A DOC is installed in the exhaust system. The DOC oxidizes hydrocarbons (HC), carbon monoxide (CO), odor causing compounds, and soluble organic fractions (SOF).Software - Software in the ECM monitors the DPF.Fault Detection and Reporting
The ECM monitors inputs from the sensors and inputs from the applications control system. Software in the ECM interprets the inputs. The software determines if the inputs are operating correctly. A diagnostic trouble code is activated when the software detects a problem with an input.The ECM broadcasts the codes on two data links. The data links are the Data Link and CAN data link. The electronic service tool must communicate on both

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.