AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1695171 - Caterpillar



1695171 ENGINE AR-COMPLETE Caterpillar parts C-12 ENGINE
Rating:
36
Alternative (cross code) number:
CA1695171
169-5171
1695171
Caterpillar 1695171 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1695171 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Related part:
1695171  SHORT BLOCK  0R9680  R

Compatible equipment models: 1695171:

TRUCK ENGINE  C-12   Caterpillar
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     6V-6640     Sealant     1    
B     -     Guide Bolt
(M8 by 80 mm)     2    
C     319-6486     Alignment Tool     1    
- Bolts
(M10 by 50 mm)     3    
D     -     Straight Edge     1    
E     1U-6396     O-Ring Assembly Compound     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the front housing is clean and free from damage. If necessary, replace the front housing.Install blanking plugs to a new front housing. Use Tooling (A) to seal all D-plugs.
Check the condition of the crankshaft front seal. If the front seal is damaged, remove the front seal from the front housing.
Clean all the mating surfaces of the cylinder block.
Illustration 1 g01337987
Install thrust washer (10) into the recess in the cylinder block. Refer to Disassembly and Assembly, "Camshaft - Install" for more information.
Illustration 2 g01338000
Install Tooling (B) to the cylinder block. Refer to Illustration 2.
Align a new joint (6) with Tooling (B) . Install the joint to the cylinder block.Note: Ensure that two circular tabs (X) on the joint are engaged in two holes (Y) in the cylinder block.
Illustration 3 g01338001
Typical example
Install Tooling (C) to the cylinder block.
Install the front housing over Tooling (B) and Tooling (C) onto the cylinder block.
Illustration 4 g01338002
(7) M8 by 20 mm (8) M8 by 35 mm (9) M8 by 25 mm
Install bolts (9) to front housing (3) finger tight.
Remove Tooling (B) .
Loosely install bolts (7) and (8) . Refer to Illustration 4 for the correct position of the bolts.
Align the bottom face of front housing (3) to the lower machined face of the cylinder block. Use a Tooling (D) and a feeler gauge in order to check the alignment between the front housing and the cylinder block. Refer to Illustration 3. Refer to Specifications, "Front Housing and Covers" for further information.
Illustration 5 g01338003
Tighten bolts (7) , (8) and (9) in the sequence that is shown in illustration 5 to a torque of 28 N m (20 lb ft). Note: Ensure that the housing and the cylinder block are correctly aligned.
Remove Tooling (C) from the cylinder block.
If necessary, install a new crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install".
Illustration 6 g01337982
Typical example
Install new O-ring seals (4) and (5) to bypass tube (1) . Use Tooling (E) in order to lubricate the O-ring seals. Install bypass tube (2) to the cylinder head. Install bolts (1) . Tighten the bolts to a torque of 22 N m (16 lb ft).End By:
Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install".
Install the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Install".
If the engine has an accessory drive, install the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install".
Install the engine oil pan. Refer to Disassembly

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.