1695193 ENGINE AR-COMPLETE Caterpillar parts C-12 ENGINE
Rating:
Alternative (cross code) number:
CA1695193
169-5193
1695193
CA1695193
169-5193
1695193
TRUCK ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
The ROP Shop | PTO Clutch CCW for Simplicity Baron XL 1694690, 1695193, 2690337, 2690338 Mower
The ROP Shop The ROP Shop replacement PTO Clutch CCW for Simplicity Baron XL 1694690, 1695193, 2690337, 2690338 Mower || Specs - Crankshaft: 1". Pulley Outside Diameter: 5 5/16". Direction: Counter Clockwise (CCW). Belt: 1/2" or 5/8". Refer to images 2 & 3 for more information || Includes - (1) PTO Clutch & (1) Installation Manual; comes as shown in the first image || Features - Heavy Duty "FatBoy Series" Upgrade. High Torque Cool Coil Upgrade. Integrated Water Tight Wire Harness. Replaceable Pulley Bearing. Super Smooth "Xtreme Precision" Machined Pulley || To prevent premature clutch failure, follow the instructions included with the clutch
The ROP Shop The ROP Shop replacement PTO Clutch CCW for Simplicity Baron XL 1694690, 1695193, 2690337, 2690338 Mower || Specs - Crankshaft: 1". Pulley Outside Diameter: 5 5/16". Direction: Counter Clockwise (CCW). Belt: 1/2" or 5/8". Refer to images 2 & 3 for more information || Includes - (1) PTO Clutch & (1) Installation Manual; comes as shown in the first image || Features - Heavy Duty "FatBoy Series" Upgrade. High Torque Cool Coil Upgrade. Integrated Water Tight Wire Harness. Replaceable Pulley Bearing. Super Smooth "Xtreme Precision" Machined Pulley || To prevent premature clutch failure, follow the instructions included with the clutch
PTO Switch for Simplicity Baron XL 18 HP, Hydro 1694670, 1694672, 1695193 Mower
Generic
Generic
The ROP Shop | Ignition Starter Key for Simplicity Baron XL 1694670, 1694672, 1695193, 2690337
The ROP Shop The ROP Shop replacement Ignition Starter Key for Simplicity Baron XL 1694670, 1694672, 1695193, 2690337 || Specs - Refer to image 2 for more information || Includes - (1) Ignition Key; comes as shown in the first image || Please be sure to check your part or model number to ensure this is the correct ignition key for your unit. Also, please note this may replace multiple parts numbers
The ROP Shop The ROP Shop replacement Ignition Starter Key for Simplicity Baron XL 1694670, 1694672, 1695193, 2690337 || Specs - Refer to image 2 for more information || Includes - (1) Ignition Key; comes as shown in the first image || Please be sure to check your part or model number to ensure this is the correct ignition key for your unit. Also, please note this may replace multiple parts numbers
For full view, you need register
Compatible equipment models: 1695193:
TRUCK ENGINE C-12
Caterpillar
Information:
Removal Procedure
Start By:
Disconnect the crankcase breather or remove the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the valve mechanism cover is equipped with a heat shield, remove the heat shield.
Illustration 1 g01353908
Typical example
Remove bolts (1) and (3) from valve mechanism cover (2).
Remove valve mechanism cover (2) from the valve mechanism cover base.
Remove joint (4) from valve mechanism cover (2). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Thoroughly clean the valve mechanism cover. Clean the mating surfaces of the valve mechanism cover base.
Illustration 2 g01353908
Typical example
Install a new joint (4) to valve mechanism cover (2). Note: Ensure that the joint is fully seated into the groove of the valve mechanism cover.
Illustration 3 g01269961
Typical example
Ensure that harness assemblies (6) are not in contact with the rocker arms or in contact with the valve mechanism cover base. Position valve mechanism cover (2) onto valve mechanism cover base (5). Ensure that harness assemblies (6) are not trapped during the assembly procedure. Install bolts (1) and (3).
Illustration 4 g01353909
Tightening sequence for the valve mechanism cover
Tighten bolts (1) and (3) in the numerical sequence that is shown in Illustration 4. Tighten the bolts to a torque of 6 N m (53 lb in).
If the valve mechanism cover is equipped with a heat shield, install the heat shield. Tighten the bolts to a torque of 9 N m (79 lb in). End By:
Connect the crankcase breather or install the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Install".
Start By:
Disconnect the crankcase breather or remove the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the valve mechanism cover is equipped with a heat shield, remove the heat shield.
Illustration 1 g01353908
Typical example
Remove bolts (1) and (3) from valve mechanism cover (2).
Remove valve mechanism cover (2) from the valve mechanism cover base.
Remove joint (4) from valve mechanism cover (2). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Thoroughly clean the valve mechanism cover. Clean the mating surfaces of the valve mechanism cover base.
Illustration 2 g01353908
Typical example
Install a new joint (4) to valve mechanism cover (2). Note: Ensure that the joint is fully seated into the groove of the valve mechanism cover.
Illustration 3 g01269961
Typical example
Ensure that harness assemblies (6) are not in contact with the rocker arms or in contact with the valve mechanism cover base. Position valve mechanism cover (2) onto valve mechanism cover base (5). Ensure that harness assemblies (6) are not trapped during the assembly procedure. Install bolts (1) and (3).
Illustration 4 g01353909
Tightening sequence for the valve mechanism cover
Tighten bolts (1) and (3) in the numerical sequence that is shown in Illustration 4. Tighten the bolts to a torque of 6 N m (53 lb in).
If the valve mechanism cover is equipped with a heat shield, install the heat shield. Tighten the bolts to a torque of 9 N m (79 lb in). End By:
Connect the crankcase breather or install the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Install".
Caterpillar SIS machinery equipment:
Caterpillar SIS
- C-12 Truck Engine 2KS00001-UP » 169-5193 ENGINE AR-COMPLETE
