1695200 ENGINE AR-COMPLETE Caterpillar parts
C-12
Rating:
Alternative (cross code) number:
CA1695200
169-5200
1695200
CA1695200
169-5200
1695200
TRUCK ENGINE,
Related part:
1695200
SHORT BLOCK
0R9680
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Superwinch 1695200 Talon 9.5 Winch
Superwinch 12 VDC winch, 9,500 lb capacity || Stainless Steel Roller Fairlead || 85' of 3/8" Wire Rope with Heavy Duty Latched Hook and Rope Thimble || 15' ergonomically sealed handheld remote with coiled cord that retracts to 4' || "Dual Stop" 100% load holding brake design provides zero drag on cable
Superwinch 12 VDC winch, 9,500 lb capacity || Stainless Steel Roller Fairlead || 85' of 3/8" Wire Rope with Heavy Duty Latched Hook and Rope Thimble || 15' ergonomically sealed handheld remote with coiled cord that retracts to 4' || "Dual Stop" 100% load holding brake design provides zero drag on cable
The ROP Shop Genuine Simplicity Foam Poly Gasket fits 1695185 1695200 1695201 1695213 1695265
The ROP Shop
The ROP Shop
Superwinch 1695200 Talon 9.5 Winch
Superwinch 12 VDC winch, 9,500 lb capacity || Stainless Steel Roller Fairlead || 85' of 3/8" Wire Rope with Heavy Duty Latched Hook and Rope Thimble || 15' ergonomically sealed handheld remote with coiled cord that retracts to 4' || "Dual Stop" 100% load holding brake design provides zero drag on cable
Superwinch 12 VDC winch, 9,500 lb capacity || Stainless Steel Roller Fairlead || 85' of 3/8" Wire Rope with Heavy Duty Latched Hook and Rope Thimble || 15' ergonomically sealed handheld remote with coiled cord that retracts to 4' || "Dual Stop" 100% load holding brake design provides zero drag on cable
For full view, you need register
Compatible equipment models: 1695200:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4389 E10 Torx Socket 1
B 385-4005 Feeler Gauge 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the valve bridges. Inspect the valve bridges for wear or damage. Replace any valve bridges that are worn or damaged.
Illustration 1 g01340041
Lubricate valve bridges (4) with clean engine oil.
Illustration 2 g01355120
The correct location of valve bridges on valve stems is shown. The electronic unit injector is not shown for clarity.
Failure to ensure that ALL valve bridges are correctly seated onto the valve stems will cause interference between the pistons and the valves, resulting in damage to the engine.
Install valve bridges (4) to the cylinder head. Note: Install used valve bridges in the original location and in the original orientation. Ensure that the valve bridges are correctly seated on the valves. New valve bridges may be installed in either orientation.
Clean the pushrods. Inspect the pushrods for wear or damage. Replace any pushrods that are worn or damaged.
Apply clean engine lubricating oil to both ends of pushrods (3). Install the pushrods to the engine with the cup upward. Note: Ensure that pushrods (3) are installed in the original location and that the ball end of each pushrod is correctly seated in the valve lifters.
Illustration 3 g01340040
Ensure that the rocker shaft assembly is clean and free from wear or damage. Install torx screws (1) in the rocker shaft.
Illustration 4 g01340044
Position rocker shaft assembly (2) onto the cylinder head. The retaining clip (6) should face the front of the engine. Note: Ensure that adjustment screws (5) are properly seated in ends of pushrods (3).
Use Tooling (A) to gradually tighten torx screws (1). Note: To avoid distortion of rocker shaft assembly (2), tighten the torx screws in the center first. Work toward the outside of the rocker shaft assembly.Tighten torx screws (1) to a torque of 35 N m (26 lb ft).
Illustration 5 g01340045
Use Tooling (B) in order to check the valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust". If necessary, adjust the valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure. End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4389 E10 Torx Socket 1
B 385-4005 Feeler Gauge 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the valve bridges. Inspect the valve bridges for wear or damage. Replace any valve bridges that are worn or damaged.
Illustration 1 g01340041
Lubricate valve bridges (4) with clean engine oil.
Illustration 2 g01355120
The correct location of valve bridges on valve stems is shown. The electronic unit injector is not shown for clarity.
Failure to ensure that ALL valve bridges are correctly seated onto the valve stems will cause interference between the pistons and the valves, resulting in damage to the engine.
Install valve bridges (4) to the cylinder head. Note: Install used valve bridges in the original location and in the original orientation. Ensure that the valve bridges are correctly seated on the valves. New valve bridges may be installed in either orientation.
Clean the pushrods. Inspect the pushrods for wear or damage. Replace any pushrods that are worn or damaged.
Apply clean engine lubricating oil to both ends of pushrods (3). Install the pushrods to the engine with the cup upward. Note: Ensure that pushrods (3) are installed in the original location and that the ball end of each pushrod is correctly seated in the valve lifters.
Illustration 3 g01340040
Ensure that the rocker shaft assembly is clean and free from wear or damage. Install torx screws (1) in the rocker shaft.
Illustration 4 g01340044
Position rocker shaft assembly (2) onto the cylinder head. The retaining clip (6) should face the front of the engine. Note: Ensure that adjustment screws (5) are properly seated in ends of pushrods (3).
Use Tooling (A) to gradually tighten torx screws (1). Note: To avoid distortion of rocker shaft assembly (2), tighten the torx screws in the center first. Work toward the outside of the rocker shaft assembly.Tighten torx screws (1) to a torque of 35 N m (26 lb ft).
Illustration 5 g01340045
Use Tooling (B) in order to check the valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust". If necessary, adjust the valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure. End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Caterpillar SIS machinery equipment:
Caterpillar SIS
- C-12 Truck Engine 2KS00001-UP » 169-5200 ENGINE AR-COMPLETE
