AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1695201 - Caterpillar



1695201 ENGINE AR-COMPLETE Caterpillar parts C-12 ENGINE
Rating:
50
Alternative (cross code) number:
CA1695201
169-5201
1695201
Caterpillar 1695201 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1695201 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
The ROP Shop Genuine Simplicity Foam Poly Gasket fits 1695185 1695200 1695201 1695213 1695265
$9.99

01 Mar 2022

US: The ROP Shop
The ROP Shop Genuine Simplicity Foam Poly Gasket fits 1695185 1695200 1695201 1695213 1695265
The ROP Shop
Superwinch 1695201 Talon 9.5SR, 12 VDC winch, 9,500 lb/4,309 kg capacity with hawse fairlead & synthetic rope
$1,259.99
 

23 Aug 2020
66.1386786[29.70] Pounds
-: -
Superwinch 1695201 Talon 9.5SR, 12 VDC winch, 9,500 lb/4,309 kg capacity with hawse fairlead & synthetic rope
Blue Anodized Aluminum Hawse || 80' of 3/8" Synthetic Rope with Heavy Duty Latched Hook and Rope Thimble || 15' ergonomically sealed handheld remote with coiled cord that retracts to 4' || "Dual Stop" 100% load holding brake design provides zero drag on cable || 12 VDC winch, 9,500 lb capacity
  For full view, you need register

Compatible equipment models: 1695201:

TRUCK ENGINE  C-12   Caterpillar

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
Illustration 1 g01340072
Typical example
Disconnect the upper radiator hose from water temperature regulator housing (1) on the cylinder head.
Illustration 2 g01340075
Typical example
Remove the air inlet hose from inlet connection (3) on inlet manifold (2).
Follow Steps 4.a and 4.b in order to disconnect harness assembly (4) from coolant temperature sensor (5).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from coolant temperature sensor (5).
Follow Steps 5.a and 5.b in order to disconnect harness assembly (4) from boost pressure sensor (6).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from boost pressure sensor (6).
Follow Steps 6.a and 6.b in order to disconnect harness assembly (4) from inlet air temperature sensor (7).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from inlet air temperature sensor (7).
Remove all cable straps that secure harness assembly (4) to the cylinder head or to the inlet manifold. The harness assembly should be positioned in order to avoid causing an obstruction during the removal of the cylinder head.
Illustration 3 g01340077
Typical example
Loosen the tube clips for tube assembly (8). Remove tube assembly (8) for the fuel return from the cylinder head and from the transfer pump. Plug the port in the transfer pump with a new plug. Cap the tube assembly with new caps.
If the engine has a wastegate solenoid, loosen the tube clips for tube assembly (9). Remove tube assembly (9) from the wastegate solenoid and from the cylinder head. Plug the port in the wastegate solenoid with a new plug. Cap the tube assembly with new caps.
Illustration 4 g01340080
Typical example
Remove bolts (10). Remove bypass tube (11) from the cylinder head. Remove O-ring seals (12) and (13) from bypass tube (11).
Illustration 5 g01340081
Illustration 6 g01340083
Sequence for tightening the bolts for the cylinder head
Gradually loosen bolts (14) in the reverse numerical order to the tightening sequence. Refer to the illustration 6. Note: Follow the correct sequence in order to help prevent distortion of the cylinder head.
Remove bolts (14) from cylinder head (15).
Illustration 7 g01340086
Typical example
Attach a suitable lifting device (16) to cylinder head (15). Support the weight of the cylinder head. The weight of the cylinder head is approximately 66 kg (145.5 lb). Note: A spreader bar must be used in order to distribute the weight of the cylinder head during the lifting operation.
Use suitable lifting device (16) to carefully lift cylinder head (15) off the cylinder block. Note: Do not use a lever to separate the cylinder head from the cylinder block. Take care not

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.