AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1695210 - Caterpillar



1695210 ENGINE AR-COMPLETE Caterpillar parts C-12 ENGINE
Rating:
58
Alternative (cross code) number:
CA1695210
169-5210
1695210
Caterpillar 1695210 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1695210 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
Superwinch 1695210 Talon 9.5i, 12 VDC winch, 9,500 lb/4,309 kg capacity with roller fairlead
$799.95
 

31 Jul 2018
9259 Hundredths Pounds
Superwinch: Superwinch
Superwinch 1695210 Talon 9.5i, 12 VDC winch, 9,500 lb/4,309 kg capacity with roller fairlead
12 VDC winch, 9,500 lb capacity || Stainless Steel Roller Fairlead || 85' of 3/8" Wire Rope with Heavy Duty Latched Hook and Rope Thimble || 15' ergonomically sealed handheld remote with coiled cord that retracts to 4' || "Dual Stop" 100% load holding brake design provides zero drag on cable
  For full view, you need register

Compatible equipment models: 1695210:

TRUCK ENGINE  C-12   Caterpillar

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
(M8 by 100 mm) 4
B 6V-6640 Sealant -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
If necessary, install the plate for the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Illustration 1 g01340664
Typical example
Install Tooling (A) to positions (X) in the cylinder block.
Illustration 2 g01340606
Typical example
Ensure that the engine oil pan (7) is clean and free from damage. Clean the isolating screws (8) and (9). Inspect the isolating screws for deterioration or damage. If necessary, replace the isolating screws. If necessary, ensure that the mating surface of the isolating frame is clean. Note: The isolating screws must be replaced as a complete set in order to ensure the correct clamping of the engine oil pan.
Position a new joint (4) onto the engine oil pan (7).
Install the isolating screws (8) and (9) to the engine oil pan. Do not install the isolating screws (8) in positions (X). Refer to Illustration 1. Note: The isolating screws are held captive by the joint.
Align the assembly of the engine oil pan with Tooling (A). Install the assembly of the engine oil pan to the isolating frame (12). Install the clip that secures the breather hose in the correct position.
Illustration 3 g01340724
(X) Position of guide studs.
(Z) Position of short isolating screws.
Tighten the isolating screws to a torque of 22 N m (16 lb ft). Tighten the isolating screws in the sequence that is shown in Illustration 3.
Remove Tooling (A).
Illustration 4 g01340725
Install the four remaining isolating screws. Tighten the isolating screws to a torque of 22 N m (16 lb ft). Tighten the isolating screws in the sequence that is shown in Illustration 4.
Install a new O-ring seal (6) to the drain plug (5). Install the drain plug (5) to the engine oil pan (7). Refer to Illustration 2. Tighten the oil drain plug to a torque of 34 N m (25 lb ft).
Illustration 5 g01340605
Typical example
If necessary, follow Steps 10.a through 10.c in order to install the assembly of the dipstick tube.
Install a new seal (3) to the tube assembly (2).
Apply Tooling (B) to the nut (1). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten the nut (1) to a torque of 18 N m (13 lb ft). Install the dipstick (not shown).
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Oil Filter Change" for the procedure.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.