AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1695211 - Caterpillar



1695211 ENGINE AR-COMPLETE Caterpillar parts C-12 ENGINE
Rating:
59
Alternative (cross code) number:
CA1695211
169-5211
1695211
Caterpillar 1695211 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1695211 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
Superwinch 1695211 Talon 9.5iSR, 12 VDC winch, 9,500 lb/4,309 kg capacity with hawse fairlead & synthetic rope
$1,099.95
 

31 Jul 2018
6614 Hundredths Pounds
Superwinch: Superwinch
Superwinch 1695211 Talon 9.5iSR, 12 VDC winch, 9,500 lb/4,309 kg capacity with hawse fairlead & synthetic rope
12 VDC winch, 9,500 lb capacity || Blue Anodized Aluminum Hawse || 80' of 3/8" Synthetic Rope with Heavy Duty Latched Hook and Rope Thimble || 15' ergonomically sealed handheld remote with coiled cord that retracts to 4' || "Dual Stop" 100% load holding brake design provides zero drag on cable
  For full view, you need register

Compatible equipment models: 1695211:

TRUCK ENGINE  C-12   Caterpillar

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
C - Loctite 5900 -
D 6V-6640 Sealant 1
E - Straight Edge 1 Note: In order to install a cast iron oil pan, the engine must be removed from the application.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the joint face of the cylinder block is clean and free from damage. Inspect the studs in the cylinder block for damage. If necessary, replace the studs.
Ensure that the engine oil pan is clean and free from damage.
Illustration 1 g01340933
Typical example
Apply a bead of Tooling (C) to positions (Y).
Illustration 2 g01340934
Align a new joint (4) with the studs and install the joint to the cylinder block.
Attach a suitable lifting device to the engine oil pan (7). The engine oil pan can weigh 100 kg (220 lb).
Use the lifting device to align the engine oil pan (7) with the studs . Install the engine oil pan to the cylinder block.
Install bolts (8) and (9), nuts (10) and the torx screws (11) finger tight.
Align the rear face of the engine oil pan to the rear face of the cylinder block. Use Tooling (E) and a feeler gauge in order to check the alignment between the engine oil pan and the cylinder block.
Illustration 3 g01399279
Typical example
Tighten bolts (8) and (9), and nuts (10) to a torque of 22 N m (16 lb ft). Use Tooling (A) in order to tighten torx screws (11) to a torque of 22 N m (16 lb ft). Tighten the fasteners in the sequence that is shown in Illustration 3.
Install a new O-ring seal (6) to drain plug (5). Install drain plug (5) to engine oil pan (7). Tighten the drain plug to a torque of 34 N m (25 lb ft).
Illustration 4 g01340605
If necessary, follow Steps 11 through 11.c in order to install the assembly of the dipstick tube.
Install a new seal (3) to tube assembly (2).
Apply Tooling (D) to nut (1). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten the nut to a torque of 18 N m (13 lb ft). Install the dipstick. Note: After the engine has been installed, ensure that the engine oil pan is filled with lubricating oil to the correct level. Refer to Operation and Maintenance Manual, "Oil Filter Change" for the correct procedure.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.