AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1695245 - Caterpillar


1695245 ENGINE AR-COMPLETE Caterpillar parts 3126B
Rating:
26
Alternative (cross code) number:
CA1695245
169-5245
1695245
Caterpillar 1695245 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1695245 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1695245:

TRUCK ENGINE  3126B   Caterpillar
  For full view, you need register

Information:


Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Illustration 1 g02022844
Park the machine on level ground. Lower the bucket to the ground so that the stick is vertical.
Move the hydraulic lockout control to the UNLOCKED position.
Turn the engine start switch to the ON position.
Move the joysticks and the travel levers/pedals to the full stroke positions in order to relieve the pressure in the pilot lines.
Turn the engine start switch to the OFF position and return the lever for the hydraulic lockout control to the LOCKED position.
Illustration 2 g02024028
Pressurized system!The hydraulic tank contains hot oil under pressure. To prevent burns from the sudden release of hot oil, relieve the tank pressure with the engine off by slowly turning the cap approximately 1/8 of a turn until the cap reaches the secondary stop.
Illustration 3 g02275615
Filler cap
(A) LOCK position
(B) PRESSURE RELEASE - START position
(C) PRESSURE RELEASE - END position
(D) OPEN position
Release the pressure that may be present in the return hydraulic circuit with the following procedure. Refer to Illustration 3 for filler cap positions.
Turn the filler cap counterclockwise, with no downward force applied, and move the arrow from position (A) to position (B).
Release the pressure for a minimum of 45 seconds by moving the arrow from position (B) to position (C).
Push the center of the filler cap down. Without tilting the filler cap, move the arrow from position (C) to position (D).
The hydraulic tank pressure is relieved. The filler cap can now be removed if needed.
Tighten the filler cap on the hydraulic tank to position (A).
Open the access door on the right side of the machine.
Illustration 4 g02160117
Clean the area in order to keep dirt out of the filter base. Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on containing fluid spillage.
Remove the used pilot filter element from the filter base. Note: Used filters should always be disposed of according to local regulations.
Clean the filter base.
Illustration 5 g00101502
Coat the seal of a new pilot filter with clean hydraulic oil.
Install the new oil filter by hand. Instructions for the installation of the filter are printed on the side of each Cat spin-on filter. For filters that are not Cat branded, refer to the installation instructions that are provided by the supplier of the filter.
Check the hydraulic oil level. Reference: For the correct procedure, refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check".
Close the access door.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

1538920 ENGINE HARNESS ASSEMBLY
120H, 135H, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.