AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1695265 - Caterpillar


1695265 ENGINE AR-COMPLETE Caterpillar parts 3406E
Rating:
70
Alternative (cross code) number:
CA1695265
169-5265
1695265
Caterpillar 1695265 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1695265 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
The ROP Shop Genuine Simplicity Foam Poly Gasket fits 1695185 1695200 1695201 1695213 1695265
$9.99

01 Mar 2022

US: The ROP Shop
The ROP Shop Genuine Simplicity Foam Poly Gasket fits 1695185 1695200 1695201 1695213 1695265
The ROP Shop
New Genuine OEM SPRING EXTENSION fits Simplicity 1695184 1695185 1695213 1695265 by The ROP Shop
$14.99
 

31 Jul 2018
19 Hundredths Pounds
The ROP Shop: The ROP Shop
New Genuine OEM SPRING EXTENSION fits Simplicity 1695184 1695185 1695213 1695265 by The ROP Shop
New Genuine OEM SPRING EXTENSION || Fits Simplicity 1695184 1695185 1695213 1695265 || Replaces OEM Simplicity 1656936SM 1656936 1685634 71656936 || Fast & Free Shipping from The ROP Shop || Quality Aftermarket Part with 1 Year Warranty
(2) Genuine OEM SPRING EXTENSIONS fit Simplicity 1695184 1695185 1695213 1695265 by The ROP Shop
$22.49
 

31 Jul 2018
38 Hundredths Pounds
The ROP Shop: The ROP Shop
(2) Genuine OEM SPRING EXTENSIONS fit Simplicity 1695184 1695185 1695213 1695265 by The ROP Shop
(2) New Genuine OEM SPRING EXTENSIONS || Fit Simplicity 1695184 1695185 1695213 1695265 || Replaces OEM Simplicity 1656936SM 1656936 1685634 71656936 || Fast & Free Shipping from The ROP Shop || Quality Aftermarket Part with 1 Year Warranty
  For full view, you need register

Compatible equipment models: 1695265:

TRUCK ENGINE  3406E   Caterpillar

Information:


Illustration 1
Corners of piston slippers must be square.
(1) Reuse
(2) Do not reuse
The piston slipper must swivel smoothly.
Illustration 2
Slipper must swivel smoothly.
The slipper end play must be 0.10 to 0.25 mm (0.004 to 0.010 in).
Illustration 3
Slipper end play limits.
(3) Push up
(4) Pull down
The piston slipper thickness for all piston assemblies in the pump must not vary more than 0.010 mm (0.0004 in) between the thickest and thinnest dimensions.
The slipper surface finish must be 0.20 to
0.63 mm (8 to 25 m in).
The depth of dimension (T) in Illustration 4 must be between 0.75 and 0.40 mm (0.030 and 0.016 in).
Illustration 4
Piston slipper thickness and surface finish.
(5) Thickest
(6) Thinnest
The fit between the piston assembly and barrel bore must be between 0.050 and 0.060 mm (.0020 and .0024 in). Dimensions (D) minus (d) equals the dimension that must be within the range.
Illustration 5
Variation between barrel bore and piston assembly diameters.
Port Plate
The port plate thickness must be a minimum of 6.6 mm (.26 in). The face indicated in Illustration 6 must have a surface finish of 0.20 mm (8 m in). The port plate flatness must not be greater than 0.005 mm (.0002 in).
Illustration 6
Inspection of port plate.
Pump Shaft
The output spline diameter of the pump shaft must measure between 44.56 and 45.67 mm (1.754 and 1.798 in) over pins. Use two 4C-5853 Pins, 4.57 mm (.180 in) diameter, for the spline measurement. These pins are not an actual pump part but a tooling device and can be ordered through Caterpillar Parts system.
Illustration 7
Measurement of pump shaft splines.
(7) Output
Shoe Retainer
The minimum height of the shoe retainer must be 12.5 mm (.49 in) after lapping. Remove wear marks from the bottom face of the shoe retainer by touch lapping, if they exceed 0.10 mm (.004 in) depth. See Illustration 8.
Illustration 8
Measurement of shoe retainer.
(8) 12.5 mm (.49 in) minimum after lapping
Drum Seal
The drum seal may be touched lapped to remove marks. The depth of the drum seal groove must be a minimum of 0.7 mm (.03 in).
Illustration 9
Measurement of drum seal groove.
(10) 0.8 mm (.03 in) minimum
Valve Plate
Wear grooves, formed on the valve plate by the drum seal, may be removed by touch lapping if they exceed 0.03 mm (.001 in) depth. The surface finish of the surface that contacts the drum seal must be 0.20 mm (8 m in).
Illustration 10
Inspection of the valve plate.
(11) Wear grooves
Cam Plate
The sliding surface of the cam plate can be touch lapped to produce a finish of 0.20 to 0.63 mm (8 to 25 m in). The minimum allowable height of dimension (H) after touch lapping is 4.5 mm (.18 in).
Illustration 11
Inspection of the cam plate.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.