AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1695290 - Caterpillar



1695290 ENGINE AR-COMPLETE Caterpillar parts 3126B ENGINE
Rating:
17
Alternative (cross code) number:
CA1695290
169-5290
1695290
Caterpillar 1695290 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1695290 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Related part:
1695290  LONG BLOCK M  0R7907  R
1695290  SHORT BLOCK  0R9964  R

Compatible equipment models: 1695290:

TRUCK ENGINE  3126B   Caterpillar
  For full view, you need register

Information:

Preferred Method
Spreader Bar
Illustration 1 g02175782
Improper lifting and improper tie-downs can allow the load to shift or fail and cause injury or damage. Use only properly rated cables and slings with lift and tie down points provided.Follow the instructions in Operation and Maintenance Manual, "Lifting and Tying Down the Machine" for the proper technique for securing the machine. Refer to Operation and Maintenance Manual, "Specifications" for specific weight information.
Illustration 2 g02161694This lifting method is the preferred method to be used for all machines. This method is the only method acceptable on machines that are equipped with threaded bosses (1) located on the counterweight.Note: The threaded bosses must only be used to remove the counterweight. These bosses will not support the weight of the machine.Note: The shipping weight that is listed is the weight of the most common configuration of the machine. If attachments have been installed on your machine, the weight of your machine and the center of gravity of your machine may vary.Refer to the Operation and Maintenance Manual, "Specifications" for specific weight information.
Use correctly rated cables and slings for lifting. The crane should be positioned so that the machine is lifted parallel to the ground.
To prevent contact with the machine, lifting cables should have sufficient length.
The width of the spreader bar and the strength of the spreader bar should be sufficient to prevent contact with the machine. When the wire cables are lifted, the wire cables should slide to front track rollers and to the rear track rollers.
Move the lever for the hydraulic lockout control to the LOCKED position. Note: Never use the step as a lifting point for lifting the machine.Additional Method (If Equipped)
Rear Eyes and Front Eyes
Illustration 3 g02175805
Improper lifting and improper tie-downs can allow the load to shift or fail and cause injury or damage. Use only properly rated cables and slings with lift and tie down points provided.Follow the instructions in Operation and Maintenance Manual, "Lifting and Tying Down the Machine" for the proper technique for securing the machine. Refer to Operation and Maintenance Manual, "Specifications" for specific weight information.
Illustration 4 g02161689This lifting method can only be used as an alternative on machines that are equipped with lifting eyes (1) located on the counterweight.Note: The shipping weight that is listed is the weight of the most common configuration of the machine. If attachments have been installed on your machine, the weight of your machine and the center of gravity of your machine may vary.Refer to the Operation and Maintenance, "Specifications" for specific weight information.
Use proper rated cables and slings for lifting. The crane should be positioned so that the machine is lifted parallel to the ground.
To prevent contact with the machine, lifting cables should have sufficient length.
Use the rear eyes and the front eyes that are provided on the lower frame to fasten tie-downs. Use corner protectors for sharp corners.
Move the hydraulic lockout control to the LOCKED position. Lifting the Machine Segments
Bucket
Illustration 5 g01587173
(1) Sleeve
(2) Bolts
(3) Pin
(4) Nuts Install pin (3) and install sleeve (1) in the brackets

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

1538920 ENGINE HARNESS ASSEMBLY
120H, 135H, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.