AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 3599208 - Caterpillar



3599208 ENGINE AR-COMPLETE Caterpillar parts C13 ENGINE
Rating:
21
Alternative (cross code) number:
CA3599208
359-9208
3599208
Caterpillar 3599208 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 3599208 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 3599208:

TRUCK ENGINE  C13   Caterpillar
  For full view, you need register

Information:


To prevent personal injury or equipment damage from failure of the hydraulic test equipment or associated circuit components because of blocked pump flow, make sure that the test equipment valves are fully open before starting the engine.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Position the machine on level ground.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "Hydraulic System Pressure - Release".
Attach 311-1362 Vacuum Cap onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 2 g00669235
Circuit diagram (1) Swing motor (2) Connector (3) Tee (4) Makeup line (5) Main control valve (6) Plug (7) Portable hydraulic tester (8) Pilot line (9) Connector at pilot pump (10) Pilot filter (12) Engine (13) Multitach group (14) Pilot pump (40) Elbow
Install the following tools in accordance with the flow meter tool layout and the circuit diagram. Refer to Illustration 1 and Illustration 2.
Install multitach group (13) on engine (12) .
Remove pilot line (8) from connector (9) at pilot pump (14) .
Install seal (49) and plug (6) to the end of pilot line (8) .
Install seal (49) and elbow (48) to connector (9) at pilot pump (14) .
Install seal (34), coupling (47), seal (34) and nipple assembly (36) to elbow (48) .
Illustration 3 g00669270
Right swing motor (1) Swing motor (2) Connector (3) Tee (4) Makeup line (40) Elbow
Disconnect makeup line (4) from connector (2) at swing motor (1) .
Assemble and install seals (30), tee (3), swivel elbow (40) and coupling (37) to connector (2) at swing motor (1) .
Remove 311-1362 Vacuum Cap and install the filler plug for the hydraulic tank.
Connect portable hydraulic tester (7) and test hoses between nipple assembly (36) at the pilot pump and coupling (37) at the swing motor.
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Illustration 4 g00344084
Portable hydraulic tester (flow meter) (7) Portable hydraulic tester (flow meter) (13) Multitach group (16) Valve (flow meter)
Turn valve (16) on portable hydraulic tester (7) clockwise until the pressure gauge on the portable hydraulic tester shows a reading of 3920 200 kPa (570 29 psi).
Record the pilot pump flow at 3920 200 kPa (570 29 psi) in Table 1.
Table 1
Pump Flow Test    
Oil Temperature C° (F°)        
Engine Speed (rpm)        
Flow Measured liter/min (US gpm)    

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.