AVSPARE.COM
parts catalog

FAN AR-VARIABLE 3599383 - Caterpillar



3599383 FAN AR-VARIABLE Caterpillar parts 324E L, 324E LN, 329E, 329E L, 329E LN FAN
Rating:
31
Alternative (cross code) number:
CA3599383
359-9383
3599383
Caterpillar 3599383 FAN AR-VARIABLE

Buy FAN AR-VARIABLE 3599383 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, MOBILE HYD POWER UNIT,

Compatible equipment models: 3599383:

EXCAVATOR  324E L   324E LN   329E L   329E LN  
MOBILE HYD POWER UNIT  329E   Caterpillar
  For full view, you need register

Information:

Introduction
Proportional Hydraulic Modulation Valves (PHMV) control the oil flow from the front pump and rear pump to the work tool. The C-T PHMV can be adjusted to control the amount of back pressure to a work tool or implement. The advantages to adjusting the back pressure are improved controllability when a heavy work tool is installed, can reduce cylinder speed for better controllability, and can help avoid a vacuum condition in the cylinder.The following can have the back pressure setting adjusted:
Boom DOWN
Stick IN
Bucket CLOSE/OPEN
Attachment Valve #1 EXTEND
Attachment Valve #1 RETRACT (If work tool is two-way flow)Note: After setting the back pressure, do NOT touch any implement levers for 5 seconds.Machine Preparation
The following procedures must be completed before performing the calibration.
Perform the main control valve calibration. Refer to Testing and Adjusting, "Main Control Valve - Calibrate" for the machine.
Perform the attachment #1 valve calibration. Refer to Testing and Adjusting, "Solenoid Valve (Proportional Reducing) - Calibrate (Attachment Valve #1)" for the machine.
Perform the Variable relief valve calibration. Refer to Testing and Adjusting, "Solenoid Valve (Proportional Reducing) - Calibrate (Variable Relief Valves)" for the tool control system for the machine.
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F). Calibration Procedure
Table 1
Default Back Pressure Values
Boom DOWN 10
Stick IN
Bucket CLOSE/OPEN
Attachment Valve #1 EXTEND
Attachment Valve #1 RETRACT(1) 6
(1) If work tool is two-way flow
Table 2
Back Pressure Setting Amount
10 Lowest amount of back pressure
1 Highest amount of back pressure Use any of the following control inputs (A) shown in Illustration 1 to calibrate the PHMV.
Illustration 1 g03366023
Electric Control Inputs for extension of the attachment control valve
(LJ) Left-hand joystick
(RJ) Right-hand joystick
(A) Thumb wheel (Forward)
(A) Switch
Select the work tool that will be attached to the machine. Reference: Refer to Testing and Adjusting, "Work Tool - Select" for the Tool Control System.Reference: Refer to Testing and Adjusting, "Work Tool Parameter - Program" for the Tool Control System.Monitor Procedure
The following procedure will allow the user to adjust the back pressure setting using the monitor.
Table 3
Back Pressure Setting
Operation Monitor Setting
Boom DOWN "BM Back Press Setting"
Stick IN "ST Back Press Setting"
Bucket CLOSE/OPEN "BKT Back Press Setting"
Attachment Valve #1 EXTEND "ATCH #1 Back Press EXT"
Attachment Valve #1 RETRACT(1) "ATCH #1 Back Press RET"(1)
(1) If work tool is two-way flow
Illustration 2 g02293918
Enter the "Service" Menu in the monitor. Enter password "9992".
Illustration 3 g02294054
Select "Tool Programming" from the "Service" menu.
Illustration 4 g02294076
Select the appropriate Tool from the "Tool Programming" menu.
Illustration 5 g03647842
Press the arrow keys on the monitor until the appropriate setting is selected. Refer to Table 3 for the operation. Press the "OK" key.
Using the arrow keys, adjust the back pressure setting between 1 and 10. Refer to Table 1 for the default values of the appropriate setting. Press the "OK" key. Do not touch any implement levers for 5 seconds.
After 5 seconds, operate the function to ensure that the desired cylinder or work tool speed is met.
If the desired speed is not met, repeat Steps 4 through 6 until desired cylinder or work tool speed is met.
Once the desired cylinder or work tool speed

Caterpillar SIS machinery equipment:

Caterpillar SIS

Cat SIS web machinery list:

Caterpillar parts catalog
330D2 L Mobile Hydraulic Power Unit HER00001-UP (MACHINE) POWERED BY C7.1 Engine
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine
324E L & 324E LN Excavators LDG00001-UP (MACHINE) POWERED BY C7.1 Engine
329E L Excavator PLW00001-UP (MACHINE) POWERED BY C7.1 Engine
329E L & 329E LN Excavators RLD00001-UP (MACHINE) POWERED BY C7.1 Engine
329E Mobile Hydraulic Power Unit K2L00001-UP (MACHINE) POWERED BY C7.1 Engine
329E L Excavator ZCD00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts fan Caterpillar catalog:

3563150 FAN GP-SUCTION
324E, 324E L, 329E, 329E L
3599384 FAN AR-SUCTION
324E, 324E L, 329E, 329E L
3563149 FAN GP-SUCTION
324E L, 324E LN, 329E, 329E L, 329E LN
1852639 FAN AS
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14H, 14H NA, 14M,...
2302892 FAN AS
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.