AVSPARE.COM
parts catalog

FASTENER GP-SWING & FINAL DR 1695527 - Caterpillar



1695527 FASTENER GP-SWING & FINAL DR Caterpillar parts 345B II, 345B II MH, 345B L FASTENER
Rating:
53
Alternative (cross code) number:
CA1695527
169-5527
1695527
Caterpillar 1695527 FASTENER GP-SWING & FINAL DR

Buy FASTENER GP-SWING & FINAL DR 1695527 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 1695527:

EXCAVATOR  345B II   345B II MH   345B L   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Clean each hose after assembly.
Tap both ends of the hose to remove any large particles.
Use one of the 233-7191, 233-7192, or 233-7193, Hose Cleaning Groups to clean the inside diameter of the hose assembly. A cleaning projectile should be sent through each end of the hydraulic hose.Note: Refer to Special Instruction, NEHS0643, Using the 233-7191, 233-7192, and 233- 7193 Hose Cleaner Groups for more detailed instructions on cleaning hoses.
Hoses that are not clean can cause hydraulic system component damage.
Operation
Crimping Hose Couplings Using Caterpillar Dies
Illustration 13 g02638520
Select the appropriate die from the Die Groups Table 1 of this manual.
Set the variable die bowl to the correct "Bowl Setting" reference number found in Special Instruction, NEEG3000, "Crimp Diameter Chart for 242-3567" or in this manual.
Illustration 14 g02638537
Find the crimp length on Special Instruction, NEEG3000, "Crimp Diameter Chart for 242-3567" and mark that length on the hose coupling.
Illustration 15 g02638586
Insert the variable die bowl into the hose machine.
Illustration 16 g02638596
Align the crimp length mark on the coupling with the top of the die.
Illustration 17 g02638606
Install the front pusher plate.
Illustration 18 g02638600
Lower the pusher plate until it touches the top of the variable crimp die bowl.
Raise the pusher plate. Remove the hose assembly, and check the crimp diameter. Refer to Special Instruction, NEEG3000, "Crimp Diameter Chart for 242-3567" for crimp diameter specifications.
If necessary, adjust the variable crimp die bowl to make the crimp diameter of the next hose assembly as close as possible to the specified crimp diameter. Write this new Bowl Setting number in the "Actual Setting" column of Special Instruction, NEEG3000, "Crimp Diameter Chart for 242-3567". Using this new number should provide a more accurate crimp diameter the next time the die is used to crimp a hose coupling.Crimping 1543 Air Conditioning Couplings
1543 Air Conditioning Couplings can be crimped using the variable die bowl by removing the 133-7362 Die Rest and using the appropriate die group. Refer to Special Instruction, NEEG3000, "Crimp Diameter Chart for 242-3567" for the "Bowl Setting" and die group part number for the coupling being assembled.For additional information, refer to Special Instruction, NEHS0749, "Crimping 1E-1543 Air Conditioning Hose and 1E-1028 Thermoplastic Hose ".
Illustration 19 g02638610
Illustration 20 g02638613
Maintenance
Clean all dirt and debris off the hose machine and counterbore of the die bowl.
Lubricate the variable crimp die bowl with 129-1939 Grease or equivalent.Inspection
Inspect the variable crimp die bowl parts daily for damage or abnormal wear. Replace all worn or damaged parts immediately.
Inspect the hydraulic power supply and high-pressure hose. Make sure that the hose connections are tight and not leaking.
Make sure that the hydraulic cylinder is not leaking. A seal kit is available to repair the cylinder.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
345B, 345B L & 345B LC Excavator 2SW00001-UP (MACHINE) POWERED BY 3176C Engine
345B L Series II Excavators AGS00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Material Handler APB00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Material Handler DET00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Excavator CCC00001-UP (MACHINE) POWERED BY 3176C Engine
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine
345B SERIES II MATERIAL HANDLER (CUSTOM) AKX00001-UP (MACHINE) POWERED BY 3176C ENGINE


Parts fastener Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.