AVSPARE.COM
parts catalog

FASTENER GP-SWING DRIVE 2278061 - Caterpillar



2278061 FASTENER GP-SWING DRIVE Caterpillar parts 325C FASTENER
Rating:
26
Alternative (cross code) number:
CA2278061
227-8061
2278061
Caterpillar 2278061 FASTENER GP-SWING DRIVE

Buy FASTENER GP-SWING DRIVE 2278061 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 2278061:

EXCAVATOR  325C   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 6 g03801398
Illustration 7 g03801416
Use Tooling (E) to tighten bearing nut (11). Install Tooling (H) on the axle housing. Place a torque wrench on the bolt at the center of Tooling (H). The torque wrench reading is equal the preload rolling torque plus the actual seal drag torque. Use the seal drag torque that was recorded in Step 10.Note: The preload rolling torque is 7 to 13 N m (62 to 115 lb in) above seal drag torque.
Illustration 8 g03801399
Illustration 9 g03801400
Use the torque wrench to rotate the axle housing assembly. Use Tooling (E) to tighten nut (11). The torque wrench reading must equal the axle bearing preload rolling torque plus the actual seal drag torque. Use the seal drag torque that was recorded in Step 10. Use the following formula to calculate the required torque wrench reading. This formula is used to measure torque at the bolt circle.Actual Torque= C x (A + B) / B"C" is the torque wrench reading."B" is the length of the torque wrench."A" is the bolt circle radius of axle housing assembly (2)."SDT" is the actual seal drag torque.
The axle shaft should have zero end play. If the axle bearing preload rolling torque exceeds the specification, back off bearing nut (11) by 1/8 turn and reseat bearing cone (12) against bearing nut (11). Perform Step 11 again.
The following steps are for the assembly of planetary carrier assembly (5):
Illustration 10 g00450743
Install retaining ring (3) in the carrier.
Illustration 11 g03883471
Apply a thin coat of clean SAE 30 oil on all parts of planetary carrier assembly (5).
Install bearing (10) in planetary gear (9).
Install thrust washers (8) and planetary gear (9) in planetary carrier assembly (5).
Illustration 12 g03883473
Illustration 13 g03883474
Illustration 14 g03883467
Install shaft (7) in carrier assembly (5). Make sure that the spring pin hole in shaft (7) is aligned with the spring pin hole in carrier assembly (5). Install a new spring pin (6A) and (6B) through carrier assembly (5) and shaft (7).
The openings of spring pin (6A) and spring pin (6B) must be 180 degrees away from each other. The openings of spring pin (6A) and spring pin (6B) must be parallel to the deck plane of carrier assembly (5).
Drive spring pins (6A) and (6B) to the depth of dimension (X) for proper engagement. The dimension (X) is 20.0 1.0 mm (0.79 0.04 inch). Refer illustration 14.
Repeat Steps 13.b through 13.g for the remaining two planetary gears.
Illustration 15 g01159051
Use Tooling (D) and a suitable lifting device to position planetary carrier assembly (5) into the axle housing assembly. The weight of planetary carrier assembly (5) is approximately 80 kg (175 lb).
Use Tooling (C) to install retaining ring (3) on axle shaft (4).
Illustration 16 g01159049
Remove axle housing assembly (2) from Tooling (B). Install the other half of the axle housing assembly on Tooling (B) in a vertical position.
Apply Tooling (J) on the mating surfaces of axle housing assembly (2) and of the differential housing.
Illustration 17 g01159047
Use Tooling (A) and a suitable lifting device to position axle housing assembly (2) onto the differential housing, as shown. The

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
325C LCR Mobile Hydraulic Power Unit BKW00001-UP (MACHINE) POWERED BY 3126B Engine


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.