parts catalog

FENDER AS 9V9219 - Caterpillar

9V9219 FENDER AS Caterpillar parts 824C, 980C FENDER
Alternative (cross code) number:
Caterpillar 9V9219 FENDER AS
Weight: 148 pounds 67 kg.

Buy FENDER AS 9V9219 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 9V9219:

WHEEL LOADER  980C   Caterpillar
Number on catalog scheme: 1
  For full view, you need register


Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1
B(1) 9U-6198 Crankshaft Turning Tool 1
B(2) 5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
C 247-5377 Torque Wrench 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (B) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft while the valve springs are removed.
Plug the apertures for the push rods in the cylinder head to prevent the entry of loose parts into the engine
Illustration 3 g02501157
Inspect valve springs (10) for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves" for further information.
If necessary, install a new valve stem seal (11) onto the valve guide.Note: The outer face of the valve guide must be clean and dry before installing the valve stem seal.
Install valve spring (10) onto the cylinder head. Position valve spring retainer (9) on valve spring (10).
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Install Tooling (A) in the appropriate position on the cylinder head to compress valve spring (10).
Apply sufficient pressure to Tooling (A) to install valve keepers (8).Note: Do not compress the spring so that valve spring retainer (9) touches valve stem seal (11).
Install valve spring keepers (8).
Carefully release the pressure on Tooling (A).
Repeat Step 2 through Step 7 for the remaining valves.
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
Remove Tooling (A).Note: If all valve springs require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following cylinders. 1 and 4 and 2 and 3. Remember that the crankshaft must not be turned while the valve springs are removed. Ensure that all the valve springs are installed before changing from one pair of cylinders to the other pair of cylinders. If all valve springs do not require replacement, the springs must be replaced in pairs.
Illustration 4 g01978813
Follow Step 10.a through Step 10.g to install the harness assemblies for electronic unit injectors (2).
Ensure that harness assembly (3) for the electronic unit injectors is clean and free from damage. Replace any damaged components.
Install a new O-ring seal (7) onto harness assembly (3) for electronic unit injectors (2).Note: Do not lubricate the O-ring seal.
Push harness assembly (3) into the cylinder head.
Install a new bolt (5) and tighten the bolt to a torque

Caterpillar parts catalog:

Caterpillar parts catalog
980C Wheel Loader 63X06575-UP (MACHINE) POWERED BY 3406 Engine

Parts fender Caterpillar catalog:

824C, 980C, 980F, 980F II
824C, 980C, 980F, 980F II
980C, 980F, 980F II
980C, 980F, 980F II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.