AVSPARE.COM
parts catalog

FILM GP-CAB 2277949 - Caterpillar



2277949 FILM GP-CAB Caterpillar parts FILM
Rating:
86
Alternative (cross code) number:
CA2277949
227-7949
2277949
Caterpillar 2277949 FILM GP-CAB

Buy FILM GP-CAB 2277949 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Secondary Filters
1. Use a strap wrench, remove the filter elements from the base. Discard the used elements.2. Clean the filter housing bases. Make sure all of the old seal is removed.3. Lubricate the sealing surface of each filter element with clean diesel fuel.4. Install the filters by hand until the sealing surface contacts the base. Tighten the element 3/4 turn. There are index rotation marks on each filter, spaced 90° (1/4 turn) apart. Use these marks as a guide when tightening the filter.5. Prime the fuel system. See "Priming the Fuel System" below.Priming the Fuel System
1. Open the fuel shutoff valve. Unlock the priming pump plunger and operate the pump.2. When there is a strong resistance to the operation of the pump plunger, lock the pump plunger. 3. Start the engine and inspect for leaks.4. If the engine will not start, reprime. If the engine is stopped, use the fuel priming pump to supply fuel to the injection lines. 5. If engine continues to misfire or smoke after starting, continue hand priming.Fuel Tank Cap and Fill Screen
Wash Cap and Screen
1. Remove the fuel tank cap. Clean the vent hole.2. Inspect the cap gasket. Replace the gasket if it is damaged.3. Remove the retaining snap ring.4. Remove the screen.5. Disassemble the cap.6. Wash all the parts in clean, nonflammable solvent.7. Lightly oil the element. Assemble the cap.8. Install the screen, the retaining snap ring and the cap.Engine Crankcase Breathers
Clean
1. Loosen the hose clamps (1) and remove the hoses from the breathers.2. Loosen clamps (2) on the breathers and remove the breathers.3. Inspect the breather seals. Use a new seal if the used one is damaged. 4. Wash the breathers in clean, nonflammable solvent.5. Clean the breather housing with a clean cloth.6. Install the breathers, elements, and hose clamps.Transmission Breather
Wash Breather
1. Remove the breather. Wash the breather in clean, nonflammable solvent. Allow the breather to dry.2. Install the clean breather.Hoist, Converter and Brake Breather Element
Change Breather Element
1. Remove the cover and clean in clean, nonflammable solvent.2. Discard the used breather element.3. Install a new element and cover.Transmission Charge and Lubrication Filters
Change Filters
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.
1. Remove the transmission charge and lubrication filter housing drain plugs and drain the oil. Clean and install the drain plugs. Removing the drain plug from the bottom of the housings, may not drain all of the oil from the housings. Be careful when removing elements and housing.2. Remove the housings and elements. Discard the used element.3. Clean the charge and lubrication filter housings in clean, nonflammable solvent.4. Inspect the seal in the filter housing bases. If the seal is damaged, replace it with a new one.5. Install the new elements in the housings. Install the housings into the bases.Check for Leaks
1. Start the engine and run it at LOW IDLE. Check for leaks.2. Observe the oil level when the oil is warm, the transmission in NEUTRAL and the parking brake engaged.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.