parts catalog

FILM-D6T XL 4645477 - Caterpillar

4645477 FILM-D6T XL Caterpillar parts FILM
Alternative (cross code) number:
Caterpillar 4645477 FILM-D6T XL

Buy FILM-D6T XL 4645477 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Illustration 1 g01322917
Schematic of the Brake/Decelerator Pedal Position SensorThis diagnostic code is associated with the Brake/Decelerator Pedal Position Sensor. The FMI 08 diagnostic means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range. The sensor is a PWM sensor that operates at a frequency of approximately 500 hertz. The sensor has an operating duty cycle of 5% to 95%. The possible causes of this diagnostic code are listed below:
The sensor has failed.
Intermittent connections or poor connections
Mechanical devices are loose.
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2305 FMI 08 is active before performing this procedure.Note: Use a Digital Multimeter for the measurements in this procedure. System Response:A level 2 warning will be generated. Functionality is lost and maximum machine speed is limited. If the brake pedal switch also has a diagnostic code active, the ECM will force the machine to neutral interlock and restrict any machine movement.Test Step 1. CHECK FOR POWER AT THE SENSOR.
Do not disconnect the harness connector from the sensor.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along contact A (wire 709-OR) for the voltage supply.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along contact B (wire J764-BR) for the ground.
Turn the key start switch and the disconnect switch to the ON position.
Measure the voltage from contact A (wire 709-OR) to contact B (wire J764-BR).Expected Result:The voltage is 10 0.5 DCV.Results:
OK - The voltage is 10 0.5 DCV. Proceed to Test Step 3.
NOT OK - The voltage is not 10 0.5 DCV. The circuit is open. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT OF THE SENSOR.
Turn the key start switch and the disconnect switch to the OFF position.
At the back of the harness connector for the sensor, remove the 7X-1710 Multimeter Probe from contact A and insert the probe along the signal wire contact C (wire M730-YL).
The other 7X-1710 Multimeter Probe remains at the ground wire contact B (wire J764-BR).
Turn the disconnect switch and the key start switch to the ON position.
Monitor the signal of the sensor with the multimeter.
Without disconnecting the sensor or the hardware that is associated with the sensor from the machine, take the sensor through the full operating range of the sensor.Expected Result:The sensor's signal responds in

Caterpillar parts catalog:

Caterpillar parts catalog
D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE HFE00001-UP (MACHINE) POWERED BY C9.3 Engine
D6 Track-Type Tractor LRG00001-UP (MACHINE) POWERED BY C9.3 Engine

Parts film Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.