AVSPARE.COM
parts catalog

FILM-D6T LGP 4645486 - Caterpillar



4645486 FILM-D6T LGP Caterpillar parts FILM
Rating:
61
Alternative (cross code) number:
CA4645486
464-5486
4645486
Caterpillar 4645486 FILM-D6T LGP

Buy FILM-D6T LGP 4645486 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01379688
Test Step 1. CHECK FOR RELATED DIAGNOSTICS
Press the "Menu" key in order to access the "Configuration" menu.
Press the "Arrow" keys until "Diagnostics" is highlighted. Press the "OK" key.
From the "Diagnostics" Menu, press the "Arrow" keys until "Fault History" is highlighted on the LCD. Press the "OK" keys.Expected Result:"CB 30" is not active.Results:
YES - "CB 30" is not active. Proceed to Test Step 2.
NO - "CB 30" is active.Repair: Proceed to Troubleshooting, "CB 30 Duplicate Sensor Serial Number".STOPTest Step 2. CHECK THE HARNESS FOR AN OPEN.
Turn the key start switch and the disconnect switch for the machine to the "OFF" position.
Disconnect the harness from the right knuckle connector.
Measure the resistance between pin "B" and pin "F".Expected Result:The resistance measurement is less than 5.0 ohms.Results:
OK - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistanceis greater than 5000 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in wire T744-WH of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK THE CONNECTOR FOR AN OPEN.
Make the following measurement at the left knuckle connector. Measure the resistance between pin "B" and pin "F".Expected Result:The resistance is less than 5.0 ohms.Results:
OK - The resistance is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 4.
NOT OK - The resistance is less than 5000 ohms. The resistance measurement is not correct. There is a short circuit in the connector.Repair: Contact "B" is shorted to wire T744-WH of the machine harness. Repair the connector or replace the connector that is located on the right hand side of the knuckle connectors.STOPTest Step 4. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts of the harness connectors and clean the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the "ON" position.
Operate the machine.
Check the status of the "EM 32".Expected Result:The "EM 32" diagnostic code is active.Results:
YES - The "EM 32" diagnostic code is active. The diagnostic code has not been corrected. Repair: Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, contact your Technical communicator for a possible consultation with Caterpillar.STOP
NO - The "EM 32" diagnostic code is not active. The diagnostic code does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP


Parts film Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.