AVSPARE.COM
parts catalog

FILM GP 4645607 - Caterpillar



4645607 FILM GP Caterpillar parts FILM
Rating:
16
Alternative (cross code) number:
CA4645607
464-5607
4645607
Caterpillar 4645607 FILM GP

Buy FILM GP 4645607 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01081042
Schematic of the Auto Select switchThis diagnostic code is associated with the Auto Select switch. The switch is connected to two inputs of the ECM. The inputs are "Normally Open" and "Normally Closed". One of the inputs is open and the other input is grounded during proper operation.The FMI 04 means that the ECM has determined that the "Normally Open" and "Normally Closed" circuitsare grounded.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected.Ensure that the diagnostic code of CID 874 FMI 04 is active before performing this procedure.System Response:When this diagnostic code is active the hydraulic control system will default to the "Service Mode" state.Test Step 1. CHECK THE SWITCH
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the switch.
Turn the key start switch and the disconnect switch to the ON position.Expected Result:The CID 874 FMI 04 has been replaced by CID 874 FMI 03.Results:
OK - The CID 874 FMI 04 has been replaced by CID 874 FMI 03. The machine harness and the ECM are correct. Proceed to Test Step 3.
NOT OK - The CID 874 FMI 04 is still active. Proceed to Test Step 2.Test Step 2. CHECK THE HARNESS
Turn the disconnect switch and the key start switch to the OFF position.
The machine harness remains disconnected from the switch.
Disconnect the machine harness connector(s) from the ECM and the switch.
Measure the resistance between contactsJ1-32 (wire Y929-GN) and J1-33 (wire Y930-BU) of the machine harness to all the contacts that are used in machine harness connectors for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
YES - Each resistance measurement is greater than 5000 ohms. The ECM has failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Troubleshooting, "Module - Replace".STOP
NO - One or more of the resistance measurements are less than 5 ohms. The harness has failed. The short is betweenJ1-32 (wire Y929-GN) and the circuit with the lowest resistance or the short is between J1-33 (wire Y930-BU) and the circuit with the lowest resistance. Repair: Repair the wiring harness or replace the wiring harness.STOPTest Step 3. CHECK THE OPERATION OF THE SWITCH.
The machine harness remains disconnected from the switch.
Connect one lead from a multimeter to contact 5 (wire J766-BR) of the harness connector for the switch.
Connect the other lead from a multimeter to contact 6 (wire Y929-GN) of the harness connector for the switch.
Measure the resistance between contact 5 (wire J766-BR) and contact 6 (wire Y929-GN). Note the resistance.
Disconnect the lead from contact 6 (wire Y929-GN) and connect the lead to contact 7 (wire Y930-BU).
Measure the resistance between contact 5 (wire J766-BR) and contact 7 (wire Y930-BU). Note the resistance.Expected Result:The

Caterpillar SIS machinery equipment:

Caterpillar SIS
  • D6T Track-Type Tractor XL, XW, LGP HNK00001-UP (MACHINE) POWERED BY C9.3 Engine » 464-5607 FILM GP
  • D6 Track-Type Tractor GZ900001-UP (MACHINE) POWERED BY C9.3 Engine » 464-5607 FILM GP
  • D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE HFE00001-UP (MACHINE) POWERED BY C9.3 Engine » 464-5607 FILM GP
  • D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE B7200001-UP (MACHINE) POWERED BY C9.3 Engine » 464-5607 FILM GP

Caterpillar parts catalog:

Caterpillar parts catalog
D6T Track-Type Tractor XL, XW, LGP HNK00001-UP (MACHINE) POWERED BY C9.3 Engine
D6 Track-Type Tractor GZ900001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE HFE00001-UP (MACHINE) POWERED BY C9.3 Engine
D6T Track-Type Tractor XL, XE; XW, XE; LGP, XE B7200001-UP (MACHINE) POWERED BY C9.3 Engine


Parts film Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.