parts catalog

FILTER AS 1C3816 - Caterpillar

1C3816 FILTER AS Caterpillar parts PR-1000, PR-450 FILTER
Alternative (cross code) number:
Caterpillar 1C3816 FILTER AS
Weight: 13 pounds 6 kg.

Buy FILTER AS 1C3816 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 1C3816:

COLD PLANER  PR-1000   PR-450   Caterpillar
Number on catalog scheme: 12
  For full view, you need register


Illustration 104 g06270970
When the fixed sensor initialization step is completed, a green circle with a check mark sign before the term "Complete" appears in the "Fixed Sensor Initialization" field. The fixed sensor initialization completed date will appear below the term "Complete". Refer to Illustration 104.Verifying 2D and 3D Guidance Accuracy
To verify the machine dimensions, use either two known good points or use a GNSS survey tool to measure points.
Park the machine on an even surface that has a clear view of the sky.
Press the Next key until the second text window appears that shows "Northing", "Easting", and "Elevation".
Verify that the GRADE display is set for "Bucket: Center".
Place the front linkage in the air and swing the machine 90+ degrees or track the machine forward approximately 1 m (3.3 ft) to ensure that the GNSS receivers have an RTK fixed position and location history.
Illustration 105 g06183285
With the bucket near the tracks, place the "Bucket: Center" focus point on the known location.Note: The known location may be replaced with a surveying rover except the linkage can obstruct a clear view of the sky and satellites without getting multi-path from signal reflections.
Note the values of the Northing, Easting, and Elevation from the GRADE display for the center focus point of the bucket.
Compare the values from the known point (or the surveyed point) and the values that are shown on the GRADE display. The values should be within two tenth of a foot.
Illustration 106 g06282401
Illustration 106 shows the Northing, Easting, and Elevation for the focus point of the bucket. The focus point is shown with the center selected.Note: The GRADE display rounds off the values. The survey tool will carry out the values to more digits. If the values are not within two tenth of a foot, then the calibration and measure-up process will need to be repeated.
Illustration 107 g06183286
Repeat Step 5 through Step 7 with a known (or surveyed) point near full reach of the front linkage.Note: Two known survey points may be used and will provide a good evaluation of the system but one known survey point may also be used if the machine position is moved to reflect the linkage positions shown.Function Checkout
Press the arrow keys until "Diagnostics" is highlightedNote: "Diagnostics" is always the last item in the list.
Press the "OK" key.A screen appears showing all the devices that are detected.
Verify that all the following components are found and configured:
GRADE display
EC520 Controller
Chassis IMU
Left and right GNSS receivers
Create a level plan or select a design by accessing the "Setup Menu > Configuration Menu", select "Design". Refer to the Operation and Maintenance Manual, M0077726, "Cat® Grade Control for 2D and 3D Excavators".
If the machine checkout is "OK", then proceed to Section "Backup GRADE System Data".Backup GRADE System Data
Save Machine Settings File
Note: This file should be stored in a safe place to help in the recovery of machine settings in the event of changing or replacing the EC520 Controller.
With the GRADE display powered and Cat GRADE application running on the screen, insert a USB flash

Caterpillar parts catalog:

Caterpillar parts catalog

Parts filter Caterpillar catalog:

0337848 FILTER
AP-1200, AP-800
320C FM, 320D, 320D FM, 320D FM RR, 324D FM, 324D FM LL, 325D FM, 330D FM, 521B, 522B, 541 2, 552 2, 568 FM LL
1850337 FILTER-OIL
24H, 350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
345B II, 345B L, 345C, 345C L, 345D L, 345D L VG, 349D, 349D L, 349E L, 349E L HVG, 349E L VG, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390...
PR-1000, PR-750B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.