AVSPARE.COM
parts catalog

FITTING, LT EGR COOLER OUTLET 7094069C1 - Caterpillar



7094069C1 FITTING, LT EGR COOLER OUTLET Caterpillar parts FITTING
Rating:
11
Alternative (cross code) number:
CA7094069C1
70940-69C1
7094069C1
Caterpillar 7094069C1 FITTING, LT EGR COOLER OUTLET

Buy FITTING, LT EGR COOLER OUTLET 7094069C1 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 11
 
  For full view, you need register

Information:

Note: SERVICE DATA: THE TOOLING IN TABLE 2 MAY NOT BE IDENTIFIED IN THE FOLLOWING PHOTOGRAPHS. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Illustration 6 g00943330
(A) Install bearings (1). The bearing must not extend beyond either face of the cylinder eye or the rod eye. (B) Apply Tooling (A) to the seal groove prior to the installation of the wiper seal (7). Lubricate the lip of wiper seal (7), seal (6) and wear ring (5) with the lubricant that is being sealed. (C) Use a 36 mm socket for the removal and for the installation of bolt (2). The torque setting for the bolt ... 850 25 N m (625 20 lb ft) (D) Lubricate piston seals (3) and wear ring (4) with the lubricant that is being sealed. (E) Lubricate O-ring seal (8), the backup ring and O-ring seal (9) with the lubricant that is being sealed. (F) Lubricate the threads of head (10) with Tooling (B). The torque setting for head (10) ... 600 130 N m (440 95 lb ft)Installation Procedure
The following procedure shows the installation for the compensating cylinder on the right side of the machine. Use the same procedure to install the compensating cylinder on the left side of the machine.
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Illustration 7 g00935779
Attach a suitable nylon lifting sling around cylinder (1) and to a suitable hoist. Make sure that the ports in the cylinder are pointing upward. Lift the cylinder toward the machine. The weight of the cylinder is approximately 20 kg (44 lb).
Illustration 8 g00925028
Install spacer (8) onto pin (7). Align the bore in cylinder (1) with pin (7) and then slide the cylinder onto the pin.
Illustration 9 g00925025
Install plate (6), bolt (5) and the washer.
Carefully lower cylinder (1) into the chassis.
Illustration 10 g00935780
Align the bore in cylinder (1) with the bores in the chassis and install pin (4). Install bolt (3) and the washer which secures the pin.
Illustration 11 g00924954
Remove the nylon lifting sling from cylinder (1) .
Illustration 12 g00924952
Connect two hoses (2) to cylinder (1) .

Caterpillar parts catalog:

Caterpillar parts catalog
CT13 SCR ON HIGHWAY TRUCK ENGINE JFB00001-UP
CT13 ON HIGHWAY TRUCK ENGINE KBK00001-UP
CT13 SCR ON HIGHWAY TRUCK ENGINE JFB00001-UP
CT13 ON HIGHWAY TRUCK ENGINE KBK00001-UP


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.