AVSPARE.COM
parts catalog

FLOOR MAT 1247412 - Caterpillar



1247412 FLOOR MAT Caterpillar parts D5M, D6M FLOOR
Rating:
26
Alternative (cross code) number:
CA1247412
124-7412
1247412
Caterpillar 1247412 FLOOR MAT
Weight: 7 pounds 3 kg.

Buy FLOOR MAT 1247412 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 1247412:

TRACK-TYPE TRACTOR  D5M   D6M   Caterpillar
Number on catalog scheme: 24
 
  For full view, you need register

Information:

Engine Specifications
Note: The front end of the engine is opposite the flywheel end of the engine. The left and the right sides of the engine are determined from the flywheel end. The number 1 cylinder is the front cylinder.
Illustration 1 g01387009
Cylinder and valve location
(A) Exhaust valve
(B) Inlet valve
Table 1
C-9 Engine Specifications
Arrangement and Cylinders In-Line 6 cylinder
Bore 112.0 mm (4.41 inch)
Stroke 149.0 mm (5.87 inch)
Aspiration ATAAC(1)
SCAC (2)
Displacement 8.8 L (537 in3)
Firing Order 1-5-3-6-2-4
Rotation (flywheel end) Counterclockwise
(1) Air-to-air aftercooled
(2) Separate circuit after coolingElectronic Engine Features
The Caterpillar C9 Engine is designed for electronic controls. The integral on board computer controls the operation of the engine. Current operating conditions are monitored. The Electronic Control Module (ECM) controls the response of the engine to these conditions and to the demands of the operator. These conditions and operator demands determine the precise control of fuel injection by the ECM. The electronic engine control system provides the following features:
Engine speed governor
Automatic air/fuel ratio control
Torque rise shaping
Injection timing control
System diagnosticsAdditional Features
The following additional features provide increased engine fuel economy and serviceability:
Cold starting capability
Tampering detection
DiagnosticsHydraulic Electronic Unit Injectors
HEUI injectors perform the following functions:
Pump the fuel.
Meter the fuel.
Time the fuel injection.The unit injectors are controlled by the ECM which uses the camshaft position and the engine speed signals from the engine speed/timing sensors and the inlet air pressure sensors. The engine's rated rpm is identified on the Information Plate.Engine Diagnostics
The engine has built-in diagnostics in order to ensure that all of the components are functioning properly. Under certain conditions, the engine horsepower and the vehicle speed may be limited. A Caterpillar electronic service tool may be used to display the diagnostic code.There are three types of diagnostic codes: active, logged and event.Most of the diagnostic codes are logged and stored in the ECM. For additional information, refer to the Operation and Maintenance Manual, "Engine Diagnostics" topic (Operation Section).The ECM provides an electronic governor that controls the injector output in order to maintain the desired engine rpm. The functionality of electronic governor is similar to the Caterpillar mechanical governor, but the electronic governor includes additional features.Engine Service Life
Engine efficiency and maximum utilization of engine performance depend on the adherence to proper operation and maintenance recommendations. In addition, use recommended fuels, coolants, and lubricants. Use the Operation and Maintenance Manual as a guide for required engine maintenance.Expected engine life is generally predicted by the average power that is demanded. The average power that is demanded is based on fuel consumption of the engine over a period of time. Reduced hours of operation at full throttle and/or operating at reduced throttle settings result in a lower average power demand. Reduced hours of operation will increase the length of operating time before an engine overhaul is required. For more information, refer to the Operation and Maintenance Manual, "Overhaul Considerations" topic (Maintenance Section).Aftermarket Products and Caterpillar Engines
Caterpillar requires the use of a 4 micron(c) secondary fuel filter for the following reasons: to maximize fuel system life and to prevent premature wear out from

Caterpillar parts catalog:

Caterpillar parts catalog
D6M & D6M LGP Track-Type Tractor 2RN00001-UP (MACHINE) POWERED BY 3116 Engine
D6M TRACK-TYPE TRACTOR XL, LGP 3WN00001-UP (MACHINE) POWERED BY 3116 Engine
D5M & D5M LGP Track-Type Tractor 3DR00001-UP (MACHINE) POWERED BY 3116 Engine
D5M & D5M LGP Track-Type Tractor 3CR00001-UP (MACHINE) POWERED BY 3116 Engine
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3116 Engine
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED BY 3116 Engine


Parts floor Caterpillar catalog:

1286072 FLOOR MAT
953C, 963C, 973C
1286071 FLOOR MAT
953C, 963C, 973C
7P8330 FLOOR MAT
943, 953, 953B, 963, 963B, 973
1209097 FLOOR MAT
933C, 939C, D3C III, D4C III, D5C III
1888224 FLOOR MAT
953C, 963C, 973C
1888221 FLOOR MAT
953C, 963C, 973C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.