AVSPARE.COM
parts catalog

FLYWHEEL A 0005598 - Caterpillar



0005598 FLYWHEEL A Caterpillar parts FLYWHEEL
Rating:
86
Alternative (cross code) number:
CA0005598
000-5598
0005598
Caterpillar 0005598 FLYWHEEL A
Weight: 0.01 pounds 0 kg.

Buy FLYWHEEL A 0005598 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
0005598-2-7/8 x 3-1/16 x 1-1/2 unhardened Split Outer Race - BERLISS - New!
$17.29
 

20 May 2021

US: Global Power
0005598-2-7/8 x 3-1/16 x 1-1/2 unhardened Split Outer Race - BERLISS - New!
Berliss
  For full view, you need register

Information:

Note: Window (1) interferes with Tooling (A) during the removal procedure. You must remove window (1) in order to remove the final drive assembly.
Remove screws (2) and remove window (1).
Illustration 2 g00828813Note: Make sure that you rotate the final drive until plug (3) is at the bottom, as shown.
Illustration 3 g00828988
Remove plug (3) and plug (4).
Drain the fluid from the final drive. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change".
Install plug (3) and plug (4).
Illustration 4 g00829004
Remove bolts (9) and guard (7). Remove bolts (5) and guard (6). Remove bolts (8) and guard (10).
Illustration 5 g00829011
Remove bolts (11) and sprocket segments (12).
Illustration 6 g00829035
Adjust the bracket on Tooling (A) until Dimension (X) is 229 mm (9.0 inch).
Illustration 7 g00830591
Attach Tooling (A) to a suitable lifting device.
Position Tooling (A) with the top of Tooling (A) through the window frame of the cab and align the bottom of Tooling (A) with the final drive assembly.
Illustration 8 g00829046
Attach Tooling (A) to the final drive assembly with Tooling (B).
Illustration 9 g00829156
Remove three bolts (13).
Illustration 10 g00829160
Install Tooling (C). Install Tooling (D).
Remove remaining bolts (13).
Illustration 11 g00829174
Turn Tooling (D) and use Tooling (A) to remove the final drive assembly from the machine. The weight of the final drive assembly is approximately 322 kg (710 lb).
Illustration 12 g00829200
Install wood block (14) between the two track drive motors, as shown.
Illustration 13 g00829341
View from the rear of the machine
Note: You must remove nuts (15) in order to remove the bearing case assembly from the machine.
Remove nuts (15) from the track drive motor.
Illustration 14 g00829222
Remove gear assembly (17) and bolts (16).
Illustration 15 g00829225
Install Tooling (E). Remove cage assembly (19) from the machine. If necessary, remove dowels (18) and dowels (20).


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.