AVSPARE.COM
parts catalog

FLYWHEEL GP 3598951 - Caterpillar



3598951 FLYWHEEL GP Caterpillar parts C1.6 FLYWHEEL
Rating:
8
Alternative (cross code) number:
CA3598951
359-8951
3598951
Caterpillar 3598951 FLYWHEEL GP

Buy FLYWHEEL GP 3598951 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE,

Compatible equipment models: 3598951:

INDUSTRIAL ENGINE  C1.6   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 2 g00357292
Use the suitable lifting device in order to raise bucket cylinder (4) until the cylinder is level. Attach a second suitable lifting device to the head end of the bucket cylinder, as shown. The weight of bucket cylinder (4) is approximately 135 kg (300 lb). Disconnect hose assemblies (5).
Remove retaining bolt (6), the washer, pin assembly (7) and the spacer. Remove bucket cylinder (4) and any shims that may be present. Disassembly and Assembly Information
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4865 Hand Hydraulic Pump 1
6V-3175 Double Acting Cylinder 1
9S-5564 Pin Puller Sleeve As 1
3H-0467 Puller Washer 1
9S-5558 Pin Puller Stud 1
1P-0544 Nut 1
1P-1835 Bearing Puller Adapter 1
B 3S-6224 Electric Hydraulic Pump Gp 1
6V-3175 Double Acting Cylinder 1
4C-9634 Puller Stud 1
9U-6832 Fast Runner Nut Assembly 1
5P-8601 Bearing Puller Adapter 1
7F-6068 Sleeve Assembly 1
C 155-0695 Thread Lock Compound 1
Illustration 3 g01334759Tooling (A) is used for the removal of bearing (1). Tooling (B) is used for the removal of bearing (3). (2) Lubricate the threads of nut (2) before assembly. Torque for the nut 3600 180 N m (2655 133 lb ft) (4) Lubricate the sealing lip with the lubricant that is being sealed. (5) Apply Tooling (C) to the groove of the wiper seal. (6) Lubricate the seals with clean grease. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
D 5P-0960 Molybdenum Grease 1
Be sure that the pin bores in the stick, in the link assemblies, and in the bucket cylinder are clean and free of dirt prior to installation of the bucket cylinder.
Illustration 4 g00357292
Typical example
Attach a suitable lifting device to bucket cylinder (4). The weight of bucket cylinder (4) is approximately 135 kg (300 lb). Be sure that the pin bores in the stick and bucket cylinder are in alignment. Also, be sure that the grease fittings in the head end and in the rod end of the bucket cylinder are facing away from the stick.
Apply Tooling (G) on pin assembly (7). Temporarily install the pin assembly. Do not remove the suitable lifting device from the bucket cylinder at this time.
Install the shims between the stick and bucket cylinder on the side opposite the retaining bolt for the pin assembly. Install the spacer and pin assembly (7). Install the washer and retaining bolt (6).
Illustration 5 g00357377
Typical example
Illustration 6 g00357378
Lower the bucket cylinder between the link assemblies. Apply Tooling (G) on pin (2). Be sure that the bore in the bucket cylinder rod is aligned with the bores in the link assemblies. Install any shims that were present during the removal procedure. Install pin (2). Install retaining bolt (1) and the nuts.
Rotate pin (2) until the pin is parallel with the link, as shown. Tighten the outside nut until the nut is 0.5 mm (0.02 inch) beyond the end of the retaining bolt, as shown. Tighten the inside nut against the outside nut to a torque of 237 40

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
C1.6 Industrial Engine C1M00001-UP


Parts flywheel Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.