AVSPARE.COM
parts catalog

FRAME AS-SUSPENSION 1246521 - Caterpillar



1246521 FRAME AS-SUSPENSION Caterpillar parts D350E, D400E, D40D FRAME
Rating:
73
Alternative (cross code) number:
CA1246521
124-6521
1246521
Caterpillar 1246521 FRAME AS-SUSPENSION
Weight: 411 pounds 186 kg.

Buy FRAME AS-SUSPENSION 1246521 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK,

Compatible equipment models: 1246521:

ARTICULATED TRUCK  D350E   D400E   D40D   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Illustration 6 g00293719
Install a Swivel Hose with clear plastic tubing in order to open the drain valve. Drain the oil into a suitable container.
Remove the Swivel Hose in order to close the drain valve.
Inspect the O-ring. Replace the O-ring if wear or damage is evident.
Clean the drain plug. Install the drain plug.
Illustration 7 g00101449
Open the access door that is located on the right side of the machine.
Clean the pump, the hydraulic lines, and the hydraulic tank.
Illustration 8 g00107986
Remove the plug from the tube. Allow the oil to drain into a container.
Inspect the O-ring. Replace the O-ring if wear or damage is evident.
Clean the plug. Install the plug and the O-ring into the drain port.Clean the Screen
Illustration 9 g00101490
(4) Bolts (5) Washers (6) Cover (7) Spring (8) Screen
Remove bolts (4), washers (5), and cover (6) .Note: Dispose of used filters and used fluids according to local regulations.Note: Do not allow spring (7) to fall into the tank.
Remove spring (7) and screen (8) .Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on containing fluid spillage.
Wash the screen in a clean nonflammable solvent. Allow the screen to dry. Inspect the screen. Replace the screen, if the screen is damaged.
Illustration 10 g00101492
(9) O-ring seal (10) O-ring seal
Remove O-ring seal (9) from the screen.
Inspect O-ring seal (9) and O-ring seal (10). Replace the O-ring seals if wear or damage is evident.
Install O-ring seal (9) on screen (8) .
Install screen (8) and spring (7). Then, install cover (6), washers (5), and bolts (4) .Note: Make sure that the O-ring seals and the spring are properly positioned during installation.Fill the Tank
Fill the hydraulic system oil tank. Refer to Operation and Maintenance Manual, "Refill Capacities".
Inspect the O-ring on the filler plug for damage. Replace the O-ring, if necessary. Clean the filler plug. Install the filler plug.
Illustration 11 g00101460
Remove the pressure cap.
Illustration 12 g00101462
Inspect the pressure cap. Clean the pressure cap. Replace the pressure cap if damage is evident.
Install the pressure cap.Fill the Pump
Illustration 13 g00107987
Note: Make no attempt to start the engine until the pump has been filled with hydraulic oil. Serious damage to the hydraulic components can result.
When the hydraulic oil has been replaced,the air must be removed from the hydraulic oil system. Use the following procedure to remove the air from the hydraulic oil system.
While the engine is stopped, remove the vent plug which is on the top of the pump. Do not install the vent plug until the pump is filled with hydraulic oil. After the pump is filled with hydraulic oil, tighten the vent plug. Start the engine. When the engine is at low idle, fully raise the boom. Hold the boom in this position.
Stop the engine. Slowly lower the boom until the bucket is on the ground. This pressurizes the hydraulic tank.
Slowly loosen the vent plug for several turns until the hydraulic oil flows out of the opening for the vent plug. This indicates that the air has been released from the pump. Tighten the plug.
Close the access door.
Start the engine. Operate the engine at

Caterpillar parts catalog:

Caterpillar parts catalog
D400E Articulated Truck 2YR00001-UP (MACHINE) POWERED BY 3406 Engine
D350E Articulated Truck 9LR00001-UP (MACHINE) POWERED BY 3406 Engine


Parts frame Caterpillar catalog:

2P5616 FRAME-DRIVE END
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 235, 24H, 30/30, 3114,...
7U8872 FRAME
D250D, D250E, D300D
1401050 FRAME AS
D250E II, D300E II
9X4723 FRAME AS-FILTER
D25D, D350E, D350E II, D400E, D400E II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.