AVSPARE.COM
parts catalog

FRAME AS-TRACK ROLLER 3156559 - Caterpillar



3156559 FRAME AS-TRACK ROLLER Caterpillar parts 325D, 325D L, 329D L, 329D LN, OEMS FRAME
Rating:
25
Alternative (cross code) number:
CA3156559
315-6559
3156559
Caterpillar 3156559 FRAME AS-TRACK ROLLER

Buy FRAME AS-TRACK ROLLER 3156559 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, UNDERCARRIAGE,

Compatible equipment models: 3156559:

EXCAVATOR  325D   325D L   329D L   329D LN  
MOBILE HYD POWER UNIT  325D  
UNDERCARRIAGE  OEMS   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Illustration 1 g00815200
Schematic of the proportional solenoid valve for traction control
This diagnostic code is associated with the proportional solenoid valve for traction control. The FMI 05 means that the ECM has determined that the current of the solenoid is below normal. The possible causes of this diagnostic code are listed below:
The energize circuit of the solenoid is open.
The return circuit of the solenoid is open.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0719 FMI 05 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:The diagnostic code will be logged into memory and the traction control system (TCS) will be disabled.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the solenoid with the active diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire 773-GY(Grey)) to contact 2 (wire K952-BR(Brown)).
Observe the status of the CID 0719 FMI 05. Expected Result:The CID 0719 FMI 05 remains active. The FMI has not changed and the "05" is still active.Results:
YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.
NO - The diagnostic is no longer active. The solenoid has failed.Repair: The solenoid has failed. Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.STOPTest Step 2. CHECK THE HARNESS FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector(s) from the ECM.
The jumper wire that was installed in the previous Test Step remains in place.
At the machine harness connector, measure the resistance from signal contact J1-17 (wire 773-GY(Grey)) to contact J1-7 (wire K952-BR(Brown)). Expected Result:The resistance is less than 5.0 Ohms.Results:
OK - The resistance is less than 5.0 Ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5000 Ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in wire 773-GY(Grey) or in wire K952-BR(Brown) of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts of the harness connectors and clean the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 0719 FMI 05. Expected Result:The CID 0719 FMI 05 is active. Results:
YES - The CID 0719 FMI 05 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has

Caterpillar parts catalog:

Caterpillar parts catalog
325 Variable Gauge Undercarriage DSL00001-UP (MACHINE)
325D L & LN Excavator GPB00001-UP (MACHINE) POWERED BY C7 Engine
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY C7 Engine
325D L Excavator GBR00001-UP (MACHINE) POWERED BY C7 Engine
325D L Excavator NAC00001-UP (MACHINE) POWERED BY C7 Engine
325D L Excavator LAL00001-UP (MACHINE) POWERED BY C7 Engine
329D L & 329D LN Excavator BFC00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator LGN00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator TPM00001-UP (MACHINE) POWERED BY C7 Engine
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator WLT00001-UP (MACHINE) POWERED BY C7 Engine


Parts frame Caterpillar catalog:

2285625 FRAME AS-TRACK ROLLER
325D, 325D L, 329D, 329D L
2285624 FRAME AS-TRACK ROLLER
325D, 325D L, 329D, 329D L
2752912 FRAME AS
325D, 325D L, 329D L
2542905 FRAME AS-UPPER
325D, 325D L, 329D, 329D L
2512772 FRAME AS-UPPER
325D, 325D L, 329D, 329D L
2276508 FRAME AS
325D, 329D L, OEMS
2276507 FRAME AS
325D, 329D L, OEMS
3156560 FRAME AS-TRACK ROLLER
325D, 325D L, 329D L, 329D LN, OEMS
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.