AVSPARE.COM
parts catalog

FRAME AS-TRACK ROLLER 3156560 - Caterpillar



3156560 FRAME AS-TRACK ROLLER Caterpillar parts 325D, 325D L, 329D L, 329D LN, OEMS FRAME
Rating:
26
Alternative (cross code) number:
CA3156560
315-6560
3156560
Caterpillar 3156560 FRAME AS-TRACK ROLLER

Buy FRAME AS-TRACK ROLLER 3156560 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, UNDERCARRIAGE,

Compatible equipment models: 3156560:

EXCAVATOR  325D   325D L   329D L   329D LN  
MOBILE HYD POWER UNIT  325D  
UNDERCARRIAGE  OEMS   Caterpillar
Number on catalog scheme: 2
 
  For full view, you need register

Information:


Illustration 1 g01102756This diagnostic code is associated with the solenoid valve (ARC supply solenoid). The FMI 06 means that the ECM has determined that the current of the solenoid is above normal. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0710 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:The diagnostic code will be logged into memory and the auto retarder system (ARC) will be disabled.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:CID 0710 FMI 06 changes to CID 0710 FMI 05 when the solenoid is disconnected.Results:
YES - CID 0710 FMI 06 changes to CID 0710 FMI 05 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.STOP
NO - CID 0710 FMI 06 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J1-18 (wire K989-BU(Blue)) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-18 (wire K989-BU(Blue)) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 0710 FMI 06. Expected Result:The CID 0710 FMI 06 is active. Results:
YES - The CID 0710 FMI 06 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". STOP
NO - The CID 0710 FMI 06

Caterpillar parts catalog:

Caterpillar parts catalog
325 Variable Gauge Undercarriage DSL00001-UP (MACHINE)
325D L & LN Excavator GPB00001-UP (MACHINE) POWERED BY C7 Engine
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY C7 Engine
325D L Excavator GBR00001-UP (MACHINE) POWERED BY C7 Engine
325D L Excavator NAC00001-UP (MACHINE) POWERED BY C7 Engine
325D L Excavator LAL00001-UP (MACHINE) POWERED BY C7 Engine
329D L & 329D LN Excavator BFC00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator LGN00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator TPM00001-UP (MACHINE) POWERED BY C7 Engine
329D L & 329D LN Excavators EBM00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine
329D L Excavator WLT00001-UP (MACHINE) POWERED BY C7 Engine


Parts frame Caterpillar catalog:

3156559 FRAME AS-TRACK ROLLER
325D, 325D L, 329D L, 329D LN, OEMS
2285625 FRAME AS-TRACK ROLLER
325D, 325D L, 329D, 329D L
2285624 FRAME AS-TRACK ROLLER
325D, 325D L, 329D, 329D L
2752912 FRAME AS
325D, 325D L, 329D L
2542905 FRAME AS-UPPER
325D, 325D L, 329D, 329D L
2512772 FRAME AS-UPPER
325D, 325D L, 329D, 329D L
2276508 FRAME AS
325D, 329D L, OEMS
2276507 FRAME AS
325D, 329D L, OEMS
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.