AVSPARE.COM
parts catalog

FRAME AS-UPPER 3157272 - Caterpillar



3157272 FRAME AS-UPPER Caterpillar parts FRAME
Rating:
71
Alternative (cross code) number:
CA3157272
315-7272
3157272
Caterpillar 3157272 FRAME AS-UPPER

Buy FRAME AS-UPPER 3157272 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g02723774
Schematic of the Transmission Oil Temperature Sensor
This diagnostic code is associated with the Transmission Oil Temperature Sensor. The FMI 04 means that the ECM has determined that the voltage of the circuit for the sensor is below normal. The possible causes of this diagnostic code are listed below:
The signal circuit for the sensor is shorted to ground.
The sensor has failed.
The ECM has failed. The failure of the ECM is unlikely. Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0177 FMI 04 is active before performing this procedure. Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Disconnect the sensor from the machine harness.
Observe the status of the diagnostic code. Expected Result:The diagnostic code remains active.Results:
OK - The diagnostic code remains active. The sensor is correct. Proceed to Test Step 2.
NOT OK - The diagnostic code changes from an FMI 04 to an FMI 03. The sensor has failed.Repair: Replace the sensor.STOPTest Step 2. CHECK THE WIRING HARNESS OF THE SENSOR FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the sensor.
Disconnect the machine harness connectors from the ECM.
At the machine harness connector for the ECM, measure the resistance from the signal contact J1-29 (wire K977-PK(Pink)) of the machine harness to ground. Measure the resistance to all contacts of the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - One or more resistance measurements are not correct. There is a short in the machine harness. The short is between signal contact J1-29 (wire K977-PK(Pink)) and ground.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, corrosion, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors in order to make sure that the connectors are fully seated. Also, make sure that the clips for each connector are fastened.
Turn the disconnect switch and the key start switch to the ON


Parts frame Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.