AVSPARE.COM
parts catalog

FUMES DISPOSAL GP 3534982 - Caterpillar



3534982 FUMES DISPOSAL GP Caterpillar parts C18, CX31-C18I, CX35-C18I FUMES
Rating:
15
Alternative (cross code) number:
CA3534982
353-4982
3534982
Caterpillar 3534982 FUMES DISPOSAL GP

Buy FUMES DISPOSAL GP 3534982 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE, PETROLEUM PACKAGE,

Compatible equipment models: 3534982:

INDUSTRIAL ENGINE  C18  
PETROLEUM PACKAGE  CX31-C18I   CX35-C18I   Caterpillar
Number on catalog scheme:
 
  For full view, you need register
3534982 Images:
Caterpillar parts 3534982
Caterpillar parts 3534982
Caterpillar parts 3534982
Caterpillar parts 3534982

Information:

Manual Adjustment of Bulldozer Blade Pitch
The standard or nominal position for the cutting edge angle is 58 degrees. This position provides optimum performance under normal conditions.Tip the blade forward in order to obtain a cutting edge angle up to 62 degrees. Tipping the blade forward provides improved penetration in hard materials.Tip the blade rearward in order to obtain a cutting edge angle up to 56 degrees. Tipping the blade rearward provides a better carrying capability of soft material.
Illustration 1 g02797613
Illustration 2 g02660157
Angle of cutting edge is an approximate number (A) Nominal position - 58 degree cutting edge in the middle position. (B) Retracted position - 56 degree cutting edge (C) Extended position - 62 degree cutting edgeThe bulldozer blade can be placed in several pitch positions such as the following pitches: the middle position (A) , the retracted position (B) and the extended position (C) .
Lower the bulldozer blade to the ground. Place the control for the lift cylinder in the FLOAT position.
Actuate the tilt cylinder in order to remove all force from the tilt brace. Stop the engine.
Remove lock pin (1) .
Keep fingers clear. Do not place your fingers into the pin holes in the tilt brace and/or push arm bracket at any time during the adjustment procedure.
Face the left-hand end of link (3) and rotate handle (2) counter clockwise to shorten the link. This position (B) has a less aggressive cutting angle and is better with loose materials.
Face the left-hand end of link (3) and rotate handle (2) clockwise to extend the link. This position (C) has a more aggressive cutting angle and is better with tougher materials.
Turn the handle until the desired cutting angle is set.
Install locking pin (1) .

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts fumes Caterpillar catalog:

3538899 FUMES DISPOSAL GP
C18, CX31-C18I, CX35-C18I
3529950 FUMES DISPOSAL GP
C15, C18, CX31-C18I, CX35-C18I
1690791 FUMES DISPOSAL GP
CS-563D, CS-573D, CS-583D
4W0709 FUMES DISPOSAL GP
D379, D379B, D398, D398B, G379, G398
2416326 FUMES DISPOSAL GP
385C, 385C FS, 385C L, 385C L MH, 390D, 390D L
1068265 FUMES DISPOSAL GP
933, 933C, 939, 939C, D3C III, D4C III, D5C III
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.