AVSPARE.COM
parts catalog

GASKET 0005636 - Caterpillar



0005636 GASKET Caterpillar parts GASKET
Rating:
51
Alternative (cross code) number:
CA0005636
000-5636
0005636
Caterpillar 0005636 GASKET
Weight: 0.01 pounds 0 kg.

Buy GASKET 0005636 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools    
Item    Pt. No.    Part Name    Qty    
A     138-7573     Link Bracket     2    
B     1U-9758     Jack Stand     1    
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00819809
Install ripper shank assemblies (13) on the ripper carriage. Refer to Operation and Maintenance Manual, "Ripper - Inspect\Replace".
Illustration 2 g00816033
Use a suitable lifting device in order to position mounting bracket (12) on the back of the machine. The weight of mounting bracket (12) is approximately 41 kg (90 lb).
Install the washers and the bolts in mounting bracket (12) .
Repeat Step 2 and Step 3 for the other mounting bracket.
Illustration 3 g00816014
Use a suitable lifting device in order to position link assembly (10) on the mounting brackets. The weight of link assembly (10) is approximately 79 kg (174 lb).
Install pin (11) and the retaining bolt.
Repeat Step 6 for pin (11) on the other side of the link assembly.
Use Tooling (B) in order to support link assembly (10) .
Remove the suitable lifting device from link assembly (10) .
Illustration 4 g01051304
Use Tooling (A) and a suitable lifting device in order to position ripper carriage (9A) on link assembly (10). The weight of the ripper carriage is approximately 317 kg (700 lb).
Install pin (9) and the retaining bolt.
Repeat Step 11 for pin (9) on the opposite side of ripper carriage (9A) .
After you install pins (9), raise the ripper assembly in order to place blocking under the carriage assembly.
Remove Tooling (B) from link assembly (10) .
Illustration 5 g00815963
Use a suitable lifting device in order to position link (6) between the carriage assembly and the mounting bracket.
Install pin (7) and pin (5). Install pin retainers (8) and the bolts.
Repeat Step 15 and Step 16 to link (6) on the other side of the ripper assembly.Note: If the hose assemblies were removed from the back of the machine during the removal procedure, perform Steps 18 and 19 in order to install the hose assemblies on the back of the machine.
Illustration 6 g00805251
Install the hose assemblies and tees (4) and (3) .
Illustration 7 g00805247
Install mounting brackets (2) and bolts (1) .End By: Install the ripper lift cylinders. Refer to Disassembly and Assembly, "Ripper Lift Cylinder - Install".


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.