AVSPARE.COM
parts catalog

GASKET 3534938 - Caterpillar



3534938 GASKET Caterpillar parts GASKET
Rating:
86
Alternative (cross code) number:
CA3534938
353-4938
3534938
Caterpillar 3534938 GASKET
Weight: 0.03 pounds 0 kg.

Buy GASKET 3534938 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 37
 
  For full view, you need register

Information:

speed dial calibrations involve submodes c01 and submode c02.Note: Always perform both the full clockwise calibration and the full counter-clockwise calibration for the speed dial.
Turn the key start switch to the ON position. Do not start the engine.
Enter calibration mode 2 on the ECM display. To do so, press and hold the ECM Mode switch until “- 2 -” is showing in the display area. Submode c01 should be displayed which will confirm that the calibration mode has been entered.
Submode c01 should be displayed if the machine is in calibration mode and the engine is not running. If submode c01 is displayed, go to Step 5. If submode c01 is not displayed, go to the next step.
Enter submode c01 (speed dial full clockwise). In order to do so, press and hold the display mode switch in the increment position until “c01” is displayed.
Ensure that the speed dial is in the full clockwise position.
Store the value of the signal currently being sent from the speed dial sensor. In order to store the value, press and hold the display mode switch in the CLEAR/STORE position. While the switch is pressed, the red indicator (not accepted) or the amber indicator (accepted) will briefly flash. Observe the status of these indicator's while the switch is in the CLEAR/STORE position. Release the display mode switch. If the amber indicator flashed (accepted), perform the next calibration.If the red indicator flashed (not accepted), check that the speed dial is in the full clockwise position. Refer to the “PWM Sensor Calibrations Are Not Accepted” module in this section of the manual. Repeat Step 6. If the red indicator is flashing again or if a diagnostic code CID 012 FMI

Caterpillar parts catalog:

Caterpillar parts catalog
CX38-P800 Powertrain Package-Well Service Transmission A3X00001-UP
CX38-P892-C18I Petroleum Power Train Package A3X00001-UP POWERED BY C18 Industrial Engine
745 Articulated Truck 3T600001-UP (MACHINE) POWERED BY C18 Engine
740EJ Articulated Truck 3T700001-UP (MACHINE) POWERED BY C18 Engine
745 Articulated Truck 3F600001-UP (MACHINE) POWERED BY C18 Engine
740 EJ Articulated Truck 3F700001-UP (MACHINE) POWERED BY C18 Engine
740 Articulated Truck 3T800001-UP (MACHINE) POWERED BY C15 Engine
740 Articulated Truck 3F800001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck TFJ00001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck LFJ00001-UP (MACHINE) POWERED BY C15 Engine
745C Articulated Truck TFK00001-UP (MACHINE) POWERED BY C18 Engine
745C Articulated Truck LFK00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck TFN00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck LFN00001-UP (MACHINE) POWERED BY C18 Engine


Parts gasket Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.