AVSPARE.COM
parts catalog

GASKET 4645181 - Caterpillar



4645181 GASKET Caterpillar parts FB221 GASKET
Rating:
24
Alternative (cross code) number:
CA4645181
464-5181
4645181
Caterpillar 4645181 GASKET

Buy GASKET 4645181 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK FELLER BUNCHER,

Compatible equipment models: 4645181:

TRACK FELLER BUNCHER  FB221   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Illustration 1 g00807537
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector, the J61/P61 machine connector, and all other connectors in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.Expected Result:All connectors, pins, and sockets should be completely inserted and coupled. The harness and wiring should be free of corrosion, abrasion, and pinch points. All connections and grounds should be tight and free of corrosion.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Shorts in the Harness from the ECM to the Digital Sensor
Illustration 2 g00807533
ECM connector P1
Disconnect ECM connector J1/P1 and the digital sensor.
Measure the resistance between P1:4 (Digital Sensor +8 VDC) and engine ground.
Measure the resistance between P1:4 (Digital Sensor +8 VDC) and P1:5 (Digital Sensor Return).
Leave the J1/P1 ECM connector and the digital sensor disconnected.Expected Result:The resistance should be greater than 20,000 Ohms for each measurement.Results:
OK - Proceed to Test Step 3.
Not OK - There is a short between the ECM and the sensor.Repair: Repair the circuit.STOPTest Step 3. Check for Open Circuits in the Harness Between the ECM and the Digital Sensor
Illustration 3 g00807533
Note: The J1/P1 ECM connector and the digital sensor should still be disconnected.
Install a jumper wire between P1:4 (Digital Sensor +8 VDC) and P1:5 (Digital Sensor Return).
Measure the resistance between terminal A (+8 VDC) and terminal B (Return) of the connector for the digital sensor.Expected Result:The resistance should be less than 10 Ohms for each measurement.Results:
OK - Proceed to Test Step 4.
Not OK - There is an open circuit in the wiring harness between the sensor and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 4. Check the Digital Sensor Supply Voltage at the Sensor Connector
Disconnect the digital sensor.
Turn the keyswitch to the ON position.
Measure the voltage across terminal A (+8 VDC) and terminal B (Return) of the connector for the digital sensor.Expected Result:The digital sensor supply voltage should be 8.0 0.5 VDC.Results:
OK - The supply voltage is reaching the sensor. Proceed to Test Step 5.
Not OK - The supply voltage is not reaching the sensor. Proceed to Test Step 7.Test Step 5. Check the Digital Sensor for an Internal Short
Install a 7X-6370 Adapter Cable (3 Pin DT Breakout) at the sensor connector, but do not connect the sensor to the breakout at this time.
Turn the keyswitch to the ON position.
Reconnect the digital sensor while you observe the voltage across terminals A (Digital Sensor +8 VDC) and B (Return) at the breakout.Expected Result:The supply voltage should be 8.0 0.5 VDC. The voltage should not drop when the sensor is connected.Results:
OK - The sensor does not have an internal short.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - The sensor may have an internal short. Proceed to Test Step 6.Test Step 6. Temporarily Install a New Sensor
Disconnect the suspect sensor and remove the suspect sensor.
Turn the keyswitch to

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
FB221 FELLER BUNCHER 8XD00001-UP (MACHINE) POWERED BY 3208 ENGINE


Parts gasket Caterpillar catalog:

9S2262 GASKET
120G, 120H, 120H ES, 120H NA, 12G, 12H ES, 12H NA, 130G, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 235, 3114, 3116, 3126, 3126B, 317...
9S2256 GASKET
120G, 12G, 130G, 140G, 14G, 160G, 16G, 235, 3114, 3116, 3208, 3304, 3306, 3306B, 3406, 3406B, 3408, 3412, 375, 578, 589, 594, 613C II, 621E, 623E, 627E, 627F, 631E, 637E, 651E, 657E, 815B, 826C, 950F,...
4M1851 GASKET
1140, 1160, 12E, 130G, 140G, 16, 1673, 1673B, 1673C, 1676, 1693, 16G, 215, 225, 235, 245, 3204, 3208, 330 L, 3304, 3306, 3306B, 3406, 3406B, 3408, 3408B, 3412, 3508, 3508B, 3512, 3516, 3606, 5130, 518...
9L8786 GASKET
1140, 1145, 1150, 1160, 215, 225, 3160, 3208, 613, 613C, 910, 931B, 943, 953, FB221, PR-1000, PS-500
9L8016 GASKET-OIL PAN
1140, 1150, 1160, 215, 225, 231D, 3160, 3204, 3208, 508, 613, 613C, 910, 931B, 943, 953, CS-551, D4HTSK II, E180, FB221, PR-1000, PS-500
9N3354 GASKET-COOLER COVER
3208, FB221, PR-1000
4W7147 GASKET-OIL COOLER
3208, FB221, PR-1000
9N0237 GASKET
225, 225D, 3208, 613B, 613C, CB-614, CS-551, FB221, PR-1000, PS-500
9L8837 GASKET
3208, 613C, 931B, FB221, PR-1000, PS-500
6L5773 GASKET
120G, 130G, 140B, 140G, 16, 1673, 1673C, 1674, 1676, 215, 225, 229, 231D, 235, 3208, 3304, 3306, 518, 613B, 613C, 621, 621R, 627, 627B, 633C, 637D, 641B, 814, 815, 920, 930, 941, 950, 951B, 955K, 955L...
9N6316 GASKET-FLYWHEEL HOUSING
225, 3208, 613B, 613C, FB221, PR-1000, PS-500
1W7810 GASKET-OUTLET
3208, 613C, FB221, G3508, PR-1000
7Y0410 GASKET
325, 325 L, 325 LN, E200B
2G7334 GASKET
120G, 130G, 518
5I7648 GASKET
320 L, 320B, 320B L, 320C, 320N
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.