AVSPARE.COM
parts catalog

GASKET 9W0228 - Caterpillar



9W0228 GASKET Caterpillar parts GASKET
Rating:
16
Alternative (cross code) number:
CA9W0228
9W-0228
9W0228
Caterpillar 9W0228 GASKET
Weight: 6 pounds 2 kg.

Buy GASKET 9W0228 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Start By:a. remove turbochargers 1. Loosen the hose clamps that hold hoses (2) to elbow (1).2. Remove hoses (2) from elbow (1). 3. Disconnect two wires (5) from the switch.4. Remove the bolts that hold elbow (1), and pull the elbow out of the aftercooler.5. Remove the bolts that hold shields (3) and (4), and remove the shields from the engine. 6. Remove two bolts (6) and remove elbow (7) from the front of the aftercooler. 7. Remove the sleeve (not shown) and adapter (8) from the rear of the aftercooler. 8. Remove the sleeve (not shown) and adapter (9) from the front of the aftercooler.9. Remove the O-ring seals from the adapters. 10. Fasten a hoist and tooling (A) to housing (10). Remove the bolts that hold the housing to the engine, and remove the housing. The weight of the housing is 78 kg (170 lb). 11. Remove the bolts that hold core assembly (11) to the engine. Fasten a hoist to the core assembly, and remove it from the engine. The weight of the core assembly is 62 kg (137 lb). 12. Remove O-ring seals (12) from each end of core assembly (11).13. Remove ring (13) and connectors (14) from the core assembly.14. Remove four O-ring seals (15) from the connectors. The following steps are for the installation of the aftercooler.15. Put O-ring seals (15) in position on connectors (14). Put glycerine on the O-ring seals.16. Put the connector in position in core assembly (11), and install ring (13). 17. Put O-ring seals (12) in position on each end of core assembly (11).18. Align the connector in the bottom of the core assembly with adapter (16). Install core assembly (11). Install the bolts that hold the core assembly in place.19. Fasten a hoist and tooling (A) to housing (10). Put the gasket and housing (10) in position, and install the spacers and bolts to hold it in place. Tighten the bolts to a torque of 55 7 N m (41 5 lbft).20. Make sure the O-ring seal is in position on adapter (9).21. Put glycerine on the bores of the adapter and the housing. Install adapter (9) and the sleeve in the front of the aftercooler.22. Make sure the O-ring seal is in position on adapter (8).23. Put glycerine on the bores of the adapter and the housing. Install adapter (8) and the sleeve in the rear of the aftercooler.24. Install elbow (7) on the front of the aftercooler.25. Install shields (3) and (4) over the exhaust manifolds.26. Make sure the gasket is in position on the cylinder block. Put elbow (1) in position in the end of the aftercooler and on the cylinder block. Install the bolts that hold it.27. Connect two wires (5) to the switch.28. Install hoses (2) on elbow (1).29. Tighten the hose clamps that hold hoses (2) to the elbow.End By:a. install turbocharger


Parts gasket Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.