parts catalog

GEAR 0005583 - Caterpillar

0005583 GEAR Caterpillar parts GEAR
Alternative (cross code) number:
Caterpillar 0005583 GEAR
Weight: 190 pounds 86 kg.

Buy GEAR 0005583 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Table 1
Required Tools    
Tooling    Part Number    Description    Qty    
A     1U-5796     Pressure Differential Gauge (Group)     1    
B     6V-7830     Pressure Gauge     1    
Table 2
Tools Needed from the 1U-5796 Pressure Differential Tool Gp    
Tooling    Item    Part Number    Description    Qty    
A     A1     177-7861     Hose As     1    
A2 6V-4143     Quick Connect Coupler     4    
A3 6V-3965     Fitting As     3    
A4 6V-4144     Quick Connect Coupler     1    
A5 8T-0861     Pressure Gauge
60000 kPa (8600 psi)     1    
A6 8C-8431     Tee     1    
A7 1U-5793     Pressure Differential Gauge Group     1    
A8 6V-0484     O-Ring Adapter     1    
A9 177-7861     Hose As     1    Test Procedure (Low Pressure Standby)
Remove the floorplates.
Illustration 3 g00866485
Pump for the implement and steering hydraulic system (1) Implement pump (signal oil pressure) (2) Implement pump (discharge pressure)
Attach Tooling (B) to pressure tap (2) and install the floorplates.
Start the engine. Run the engine at high idle. Make sure that the parking brake is engaged.
Move all the control levers into the HOLD position.
The correct reading on Tooling (B) is 3000 kPa (435 psi), which is the output pressure of the pump in the low pressure standby condition. If the pressure reading is below 2000 kPa (290 psi) or above 3700 kPa (535 psi), check the margin pressure setting. Refer to the test for margin pressure in Testing and Adjusting, "Pump Discharge Pressure - Test".
Move the tiller handle back and forth to the stops for steering. Release the tiller. If the pressure on the tetragauge does not return to the reading from Step 5, the steering linkage should be adjusted.
Adjustments to the pump output should not be made based on the results of the test. If the reading is not correct, run the margin pressure test.Test Procedure (High Pressure Cutoff)
Assemble Tooling (A). Refer to Illustration 1 for the orientation of the parts. Refer to Table 2 for the required parts information.
Remove the floorplates.
Illustration 4 g00866485
Pump for the implement and steering hydraulic system (1) Pressure tap for the signal oil (2) Tap for the pump discharge pressure
Attach hose (A1) to pressure tap (2). Attach hose (A9) to pressure tap (1) .
Start the engine. Run the engine at high idle. Release the parking brake. Activate the service brakes.
Move the tiller handle to a position between HOLD and the MID STEER LEFT POSITION.
The correct reading on Tooling (A5) is 38000 700 kPa (5500 100 psi). This pressure is the output pressure of the pump in the condition of high pressure stall. The reading for the pressure differential should be below 345 kPa (50 psi) with a maximum oil temperature of 66°C (151°F).
If the high pressure reading is not correct, the pressure cutoff spool should be adjusted. Refer to Testing and Adjusting, "Pump Control Valve (Steering) -

Parts gear Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.