parts catalog

GEAR-PLANETARY 1C3880 - Caterpillar

1C3880 GEAR-PLANETARY Caterpillar parts PR-105 GEAR
Alternative (cross code) number:
Caterpillar 1C3880 GEAR-PLANETARY
Weight: 0.46 pounds 0 kg.

Buy GEAR-PLANETARY 1C3880 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 1C3880:

COLD PLANER  PR-105   Caterpillar
Number on catalog scheme: 12
  For full view, you need register


Machine Shipping
Investigate the travel route for overpass clearances. Make sure there will be adequate clearance for the machine being transported.To prevent the machine from slipping while loading, or shifting in transit, remove ice, snow or other slippery material from the loading dock and the truck bed before loading. Obey all state and local laws governing the weight, width and length of a load.Remove the starting aid (ether) cylinder, if equipped.Make sure the cooling system has proper antifreeze if moving machine to a colder climate.Observe all regulations governing wide loads. 1. Block the trailer or rail car wheels before loading (trailer shown).2. After the machine is in position, connect the frame lockpin to hold the front and rear frames rigid.3. Install the wheel lean bolt in the wheel lean bracket to position the front wheels for shipping.4. Lower the equipment to the floor of the transport vehicle. Move the transmission control lever to Neutral.5. Engage the parking brake.6. Stop the engine.7. Turn the start switch key to OFF and remove the key.8. Turn the disconnect switch key to OFF and remove the key.9. Lock the doors, access covers and attach any vandalism protection.10. Secure the machine with tiedowns when transporting on a rail car or a tractor-trailer.11. Cover the exhaust opening. Turbocharger (if equipped) damage can result if turbocharger rotates without the engine operating.Machine Roading
Before roading a machine, consult your tire dealer for recommended tire pressures and speed limitations.TON km/h (TON MPH) limitations must be observed. Consult your tire dealer for the speed limit of the tires involved.When traveling long distances, stop every 40 km (25 miles) or 1 hour for 30 minutes to allow the tires and components to cool.Inflate the tires to the correct pressure.Use a self-attaching inflation chuck and stand behind the tire tread while inflating the tire. See Tire Inflation Information.Perform a Walk-Around Inspection and measure the fluid levels in the various compartments.Check with the proper officials to obtain the required permits, etc.Travel at a moderate speed. Observe all speed limitations when roading the machine.Machine Lifting - Tiedown Information
Improper lifting or tiedowns can allow load to shift and cause injury or damage.
1. Weight and instructions given herein apply to units manufactured by Caterpillar Inc. 143H - NA Version Weight 16 850 kg (37,100 lb)163H - NA Version Weight 18 215 kg (40, 100 lb)2. Use proper rated cables and slings for lifting. Position crane for level machine lifting.3. Spreader bar widths should be sufficient to prevent contact with machine.4. Use the two rear and two front holes provided for tiedowns.Install tiedowns at several locations, and block wheels front and rear.Check appropriate laws governing weight, width and length of load.Contact your Caterpillar dealer for shipping instructions for your machine.

Caterpillar parts catalog:

Caterpillar parts catalog

Parts gear Caterpillar catalog:

PR-105, PR-450, PR-450C
0817105 GEAR-SUN
PR-105, PR-450, PR-450C
9N8343 GEAR
PR-105, PR-450, PR-450C
9N8347 GEAR
PR-450, PR-750B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.