AVSPARE.COM
parts catalog

GEAR 4646256 - Caterpillar



4646256 GEAR Caterpillar parts GEAR
Rating:
76
Alternative (cross code) number:
CA4646256
464-6256
4646256
Caterpillar 4646256 GEAR
Weight: 3 pounds 1 kg.

Buy GEAR 4646256 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 15
 
  For full view, you need register

Information:

Cat Monitoring System
The engine is equipped with a programmable Cat Monitoring System. The Electronic Control Module (ECM) monitors the operating parameters of the engine. The ECM can initiate responses if a specific engine parameter exceeds an acceptable range. Three possible responses may be available for each parameter: "", "DERATE" and "SHUTDOWN". Some of the responses are not available for some of the parameters. An ET service tool is used to perform the following activities:
Select the available responses.
Program the level for monitoring.
Program delay times for each response.The default settings for the parameters are programmed at the factory. To accommodate unique applications and sites, the parameters may be reprogrammed with an ET service tool.The screens of the ET service tool provide guidance for the programming. The following options can be programmed "ON" or "OFF": "", "DERATE" and "SHUTDOWN".The screens of the ET service tool also provide guidance for changing setpoints. For information on programming the Cat Monitoring System, use the appropriate ET service tool and see the Service Manual, "Troubleshooting" module.The Cat Monitoring System is enabled after the engine is started. When the engine rpm exceeds 50 rpm below low idle, the ECM begins checking parameters. The ECM monitors the parameters in order to determine if the parameters exceed the setpoints.If the monitoring system initiates a warning, a deration, or a shutdown, the event is logged into the ECM. This procedure occurs even if the parameter is programmed "OFF". If a setpoint for a parameter is exceeded, the event will be logged.Any failure of a sensor will result in disabling the corresponding portion of the monitoring system. The failure of a sensor will cause an "ACTIVE" diagnostic code for the sensor.The derating is cumulative. For example, a derating of 5 percent followed by a derating of 2 percent results in a total derating of 7 percent. If the conditions that cause the derating are not corrected, the derating will continue.Default Settings for the Cat Monitoring System
Derate - A reduction of engine horsepower in response to an abnormal operating condition.Setpoint - A specific value which can activate the following responses: warning, deration and shutdown. The setpoint can be a pressure, a speed, a temperature, or a voltage.Hysteresis - The change in the signal from a sensor that is tolerated by the ECM. The difference between the setpoint that activates a response and the value that deactivates the response. For example, a warning for low voltage can activate if a value below 20 V is detected by the ECM. The voltage must rise to 22 V in order to clear the warning. The hysteresis is the 2 V that are above the 20 V.Note: For specific information concerning the default settings for the monitoring system, refer to the Troubleshooting Manual, KENR9173.

Caterpillar parts catalog:

Caterpillar parts catalog
930M Small Wheel Loader HEY00001-UP (MACHINE) POWERED BY C7.1 Engine
930K ADL (Air Deployable Loader) HEG00001-UP (MACHINE) POWERED BY C7.1 Engine
924K Wheel Loader PWR00001-UP (MACHINE) POWERED BY C6.6 Engine
930K Wheel Loader RHN00001-UP (MACHINE) POWERED BY C6.6 Engine
938K Wheel Loader SWL00001-UP (MACHINE) POWERED BY C6.6 Engine
924K Small Wheel Loader ENC00001-UP (MACHINE) POWERED BY C7.1 Engine
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine
930K Small Wheel Loader DYB00001-UP (MACHINE) POWERED BY C7.1 Engine
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine
938K Small Wheel Loader HFW00001-UP (MACHINE) POWERED BY C7.1 Engine
938K Small Wheel Loader XXT00001-UP (MACHINE) POWERED BY C7.1 Engine
930K Military Fork Lift TNY00001-UP (MACHINE)
926M Small Wheel Loader LTE00001-UP (MACHINE) POWERED BY C7.1 Engine
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine
938M Small Wheel Loader J3R00001-UP (MACHINE) POWERED BY C7.1 Engine
938K Small Wheel Loader W8K00001-UP (MACHINE) POWERED BY C7.1 Engine
930K Small Wheel Loader FRK00001-UP (MACHINE) POWERED BY C7.1 Engine
924K Small Wheel Loader SNZ00001-UP (MACHINE) POWERED BY C7.1 Engine
938K Small Wheel Loader REP00001-UP (MACHINE) POWERED BY C7.1 Engine
924K Small Wheel Loader KW400001-UP (MACHINE) POWERED BY C7.1 Engine
930K Small Wheel Loader P3K00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts gear Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.