AVSPARE.COM
parts catalog

GEAR 9V9357 - Caterpillar



9V9357 GEAR Caterpillar parts 215, 215B GEAR
Rating:
39
Alternative (cross code) number:
CA9V9357
9V-9357
9V9357
Caterpillar 9V9357 GEAR
Weight: 27 pounds 12 kg.

Buy GEAR 9V9357 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 9V9357:

EXCAVATOR  215   215B   Caterpillar
  For full view, you need register

Information:


Illustration 1 g01135723
Schematic of the Swing Pump Swashplate SolenoidThis diagnostic code is associated with the Swing Pump Swashplate Solenoid. The FMI 06 means that the ECM has determined that there is a short to ground in the circuit. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1150 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:CID 1150 FMI 06 changes to CID 1150 FMI 05 when the solenoid is disconnected.Results:
YES - CID 1150 FMI 06 changes to CID 1150 FMI 05 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Stop.
NO - CID 1150 FMI 06 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J2-9 (wire P959-GN) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-9 (wire P959-GN) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. Stop.Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 1150 FMI 06. Expected Result:The CID 1150 FMI 06 is active. Results:
YES - The CID 1150 FMI 06 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NO - The CID 1150 FMI 06 is not active. The diagnostic code does not exist at this time.

Caterpillar parts catalog:

Caterpillar parts catalog
215B EXCAVATOR 9YB00001-UP (MACHINE) POWERED BY 3304 ENGINE
215B SA EXCAVATOR 4FC00001-UP (MACHINE) POWERED BY 3304 ENGINE
215 EXCAVATOR 14Z00649-UP (MACHINE) POWERED BY 3204 ENGINE
215B EXCAVATOR 2XC00001-UP (MACHINE) POWERED BY 3204 ENGINE


Parts gear Caterpillar catalog:

3V5317 GEAR (13 teeth)
215, 225, 225D, 229, FB221
3V5378 GEAR (36 teeth)
215, 225, 225D, 229, FB221
5V7222 GEAR-FINAL DRIVE
215, 225, 225D, 229, FB221
7V7973 GEAR
215, 225, 229
9T3408 GEAR
215B, 225, 231D, 320 L, 320B, 321B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 539, E300B, M325B
9M6580 GEAR ASSEM.
657, 955H, D320A
1026503 GEAR-PLANETARY
311, 311B, 312, 315, 317, OEMS
1026523 GEAR-SUN
311, 311B, 312, 315, 317, OEMS
1026522 GEAR-SUN
311, 311B, 312, 315, 317, OEMS
1026520 GEAR-SUN
311, 311B, 312, 315, 317, OEMS
1026534 GEAR-RING
311, 311B, 312, 315, 317, OEMS
1026513 GEAR-PLANETARY
311, 311B, 312, 315, 317, OEMS
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.