AVSPARE.COM
parts catalog

GEAR AS 9V9358 - Caterpillar



9V9358 GEAR AS Caterpillar parts 215, 215B GEAR
Rating:
38
Alternative (cross code) number:
CA9V9358
9V-9358
9V9358
Caterpillar 9V9358 GEAR AS
Weight: 16 pounds 7 kg.

Buy GEAR AS 9V9358 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 9V9358:

EXCAVATOR  215   215B   Caterpillar
  For full view, you need register

Information:


Illustration 1 g01135723
Schematic of the Swing Pump Swashplate SolenoidThis diagnostic code is associated with the Swing Pump Swashplate Solenoid. The FMI 05 means that the ECM has determined that an open in the circuit exists. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is open.
The return circuit of the solenoid is open.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1150 FMI 05 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the solenoid with the active diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire P959-GN) to contact 2 (wire H716-WH).
Observe the status of the CID 1150 FMI 05.Expected Result:The CID 1150 FMI 05 remains active. The FMI has not changed and the "05" is still active.Results:
YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.
NO - The diagnostic is no longer active. The solenoid has failed.Repair: The solenoid has failed. Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem. Stop.Test Step 2. CHECK THE HARNESS FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector(s) from the ECM.
The jumper wire that was installed in the previous Test Step remains in place.
At the machine harness connector, measure the resistance from signal contact J2-9 (wire P959-GN) to contact J2-18 (wire H716-WH).Expected Result:The resistance is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in wire P959-GN or in wire H716-WH of the machine harness. Repair the machine harness or replace the machine harness. Stop.Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts of the harness connectors and clean the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 1150 FMI 05.Expected Result:The CID 1150 FMI 05 is active. Results:
YES - The CID 1150 FMI 05 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting,

Caterpillar parts catalog:

Caterpillar parts catalog
215B EXCAVATOR 9YB00001-UP (MACHINE) POWERED BY 3304 ENGINE
215B SA EXCAVATOR 4FC00001-UP (MACHINE) POWERED BY 3304 ENGINE
215 EXCAVATOR 14Z00649-UP (MACHINE) POWERED BY 3204 ENGINE
215B EXCAVATOR 2XC00001-UP (MACHINE) POWERED BY 3204 ENGINE


Parts gear Caterpillar catalog:

3V5317 GEAR (13 teeth)
215, 225, 225D, 229, FB221
3V5378 GEAR (36 teeth)
215, 225, 225D, 229, FB221
5V7222 GEAR-FINAL DRIVE
215, 225, 225D, 229, FB221
7V7973 GEAR
215, 225, 229
9T3408 GEAR
215B, 225, 231D, 320 L, 320B, 321B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 539, E300B, M325B
9M6580 GEAR ASSEM.
657, 955H, D320A
1026523 GEAR-SUN
311, 311B, 312, 315, 317, OEMS
1026522 GEAR-SUN
311, 311B, 312, 315, 317, OEMS
1026520 GEAR-SUN
311, 311B, 312, 315, 317, OEMS
1026534 GEAR-RING
311, 311B, 312, 315, 317, OEMS
1026513 GEAR-PLANETARY
311, 311B, 312, 315, 317, OEMS
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.