AVSPARE.COM
parts catalog

GENERATOR GP 4647410 - Caterpillar



4647410 GENERATOR GP Caterpillar parts GENERATOR
Rating:
21
Alternative (cross code) number:
CA4647410
464-7410
4647410
Caterpillar 4647410 GENERATOR GP

Buy GENERATOR GP 4647410 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 444-0978 Valve Guide Driver 1 Start By:
Remove the inlet valves and the exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Removal and installation of the valve guide and valve seat must be carried out by personnel with the correct training. Also special machinery is required. For more information, refer to your authorized Caterpillar dealer.
Illustration 1 g03003636
Use Tooling (A) in order to remove valve guides (2) from cylinder head (1).
Repeat the Step 1 for the remaining valve guides. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 444-0978 Valve Guide Driver 1
435-3148 Stop Collar 1
B 442-7298 Valve Guide Reamer 1
Removal and installation of the valve guide and valve seat must be carried out by personnel with the correct training. Also special machinery is required. For more information, refer to your authorized Caterpillar dealer.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the parent bores in the cylinder head for the valve guides.
Illustration 2 g03003639
Lubricate a new valve guide (2) and place the valve guide in position. Carefully tap the valve guide in order to start the installation. Use Tooling (A) to install the valve guide into the cylinder head.
Repeat Step 2 for the remaining valve guides.
Illustration 3 g03005596
Check protrusion (X) of valve guides (2). The valve guides should protrude 8.5 0.15 mm (0.33465 0.00591 inch) above the valve spring recess. Refer to Specifications, "Cylinder Head Valves" for more information.
After installation of valve guides (2), the valve guides must be reamed to the finished diameter. Follow Steps 5.a through 5.c in order to ream the valve guides.
Lubricate the bores of valve guides (2) with clean engine oil.
Use Tooling (B) in order to ream the valve guides. Ensure that even pressure is applied to Tooling (B).
Ensure that the cylinder head is clean and free from machining debris.
Check the finished diameter of valve guides (2). Refer to Specifications, "Cylinder Head - Valves" for more information.
Check the depths of the valves below the face of the cylinder head. Refer to System Operation, Testing and Adjusting, "Valve Depth - Inspect" for more information. End By:
Install the inlet valves and the exhaust valves. Refer to Disassembly and Assembly , "Inlet and Exhaust Valves - Remove and Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
C15 Generator Set AR200001-UP
C18 Generator Set AR300001-UP


Parts generator Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.