AVSPARE.COM
parts catalog

GUARD-HOSE 2278134 - Caterpillar



2278134 GUARD-HOSE Caterpillar parts 623G GUARD
Rating:
63
Alternative (cross code) number:
CA2278134
227-8134
2278134
Caterpillar 2278134 GUARD-HOSE
Weight: 2 pounds 0 kg.

Buy GUARD-HOSE 2278134 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SCRAPER,

Compatible equipment models: 2278134:

WHEEL SCRAPER  623G   Caterpillar
Number on catalog scheme: 21
 
  For full view, you need register

Information:


Illustration 1 g02566258
Connections for “Ladder Position Proximity” Switch
This diagnostic code is associated with the “Ladder Position Proximity” Switch. The switch supplies two switch-to-ground inputs to the "Transmission/Chassis ECM". The ECM expects one of the two inputs of the switch to be grounded at all times. When the ECM detects that both inputs of the switch are grounded at the same time, the ECM activates an FMI 04 diagnostic code. The FMI 04 diagnostic code indicates a “voltage below normal” condition.Some conditions that can cause this diagnostic code are listed below:
One or both of the switch inputs is shorted to a ground source.
The switch has failed.
The ECM has failed. A failure of the Transmission/Chassis ECM is unlikely. Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, that all connections are secure and that all connections are in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.
Table 1
States of “Ladder Position Proximity” Switch Contact
Ladder Extended N/O Input J1-34 (wire E457-GY(Grey)) N/C Input J1-35 (wire E788-BU(Blue))
Ladder Retracted Open(1) Closed(2)
“Ladder Position” Switch Open Closed
(1) Open to ECM return J2-22 (J766-PU(Purple) - ground).
(2) Closed to ECM return J2-22 (J766-PU(Purple) - ground).Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Test Step 1. CHECK THE SWITCH
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Connect a laptop, with the latest version of Cat ET, to the ET connector. Use the Cat ET program on the laptop to monitor the status of the diagnostic code.
Observe the status of the diagnostic code while the connector of the switch is disconnected from the machine harness. Reconnect the switch and disconnect the switch again. Observe the status of the diagnostic code. Expected Result:The active CID 3629 FMI 04 diagnostic code remains the same when the switch is disconnected. Results:
OK - The CID 3629 FMI 04 diagnostic code remains the same . Proceed to Test Step 2.
NOT OK - The CID 3629 FMI 04 diagnostic code is NO longer active. A CID 3629 FMI 03 diagnostic code becomes active when the connector of the switch is disconnected. The machine harness and the ECM are operating correctly. The switch has failed.Repair: Replace the “Operator Present” switch. After replacement of the switch, verify that the operation of the new switch is correct before operating the machine. STOPTest Step 2. CHECK THE HARNESS FOR A SHORTThe switch remains disconnected from the machine harness.
Disconnect the machine harness connectors J1 and J2 from the "Transmission/Chassis ECM".
At the machine harness connector of the ECM J1, measure the resistance between contact J1-35 (wire E788-BU(Blue)) and frame ground. Measure the resistance between contact J1-35 (wire E788-BU(Blue)) to

Caterpillar parts catalog:

Caterpillar parts catalog
623G Wheel Scraper CEW00001-UP (MACHINE)
623G Wheel Scraper DBY00001-UP (MACHINE)


Parts guard Caterpillar catalog:

2994004 GUARD GP-ELEVATOR
623G, 623H, 623K, 623K LRC
8I1629 GUARD AS
623F, 623G, 623H, 623K, 623K LRC
1714141 GUARD AS
621G, 623G, 627G, 631G, 637G
2750137 GUARD AS
621G, 623G, 627G, 631G, 637G, 657G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.