AVSPARE.COM
parts catalog

GUARD AS 3598672 - Caterpillar



3598672 GUARD AS Caterpillar parts 320E, 320E RR GUARD
Rating:
34
Alternative (cross code) number:
CA3598672
359-8672
3598672
Caterpillar 3598672 GUARD AS
Weight: 5 pounds 2 kg.

Buy GUARD AS 3598672 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3598672:

EXCAVATOR  320E   320E RR   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Release all the pressure in the hydraulic system prior to disconnecting any hydraulic lines or removing any loader linkage pins. If the hydraulic oil pressure is not released completely, oil can spray out of the oil lines under high pressure. Also, there will be binding of the loader linkage pins in their bores. After the removal of any pins, the loader linkage can separate suddenly. Failure to release system pressure completely can cause personal injury.
1. Release all the pressure from the hydraulic system. The bucket/implement positioner group (4) must be removed from the right hand tilt cylinder only.2. Disconnect tube (1) at the rear of the tilt cylinder and also at junction block (2).3. Remove bolts (6) (not shown) that holds positioner bracket (3) to the tilt cylinder.4. Remove bucket/implement positioner group (5) from the right hand tilt cylinder. 5. Fasten a nylon strap to the tilt cylinder and attach a hoist.6. Remove two bolts and lockplate (8).7. Remove pin (7) from the rod end of the tilt cylinder. 8. Fasten a second nylon strap and raise the tilt cylinder until it is level.9. Remove bolt and plate (9) from the tilt cylinder head end.10. Disconnect hydraulic lines (11), (12) and (13) from the tilt cylinder and then lay them aside.11. Remove the bolt and pin (10) from the head end of the tilt cylinder.12. Remove the tilt cylinder from the machine.13. The weight of the tilt cylinder is 45 Kg (100 lb). 14. Remove lip seals (14) from each side of the bearing in the head end of the cylinder. 15. Use tooling (A) and then remove the bearing from the head end of the tilt cylinder. The following steps are for the installation of the tilt cylinder.16. Lower the temperature of the bearing and use tooling (A) to install it in the head end of the tilt cylinder until it is centered in the bore.17. Use tooling (B) and install a new lip seal (14) on each side of the bearing.18. Be sure the lips of the seals point toward the outside.19. Be sure the pins slide freely in their bores before assembly. Lubricate all pins, pin bores and seals with 5P0960 Multipurpose Grease before assembly.20. Install the tilt cylinders in the reverse order of the removal.21. Adjust the bucket/implement positioner group (right hand only).22. See Bucket/Implement Positioner Group Adjustment Procedures in IT12F Integrated Toolcarrier Hydraulic System in Testing And Adjusting.

Caterpillar parts catalog:

Caterpillar parts catalog
320E & 320E L Excavators AWS00001-UP (MACHINE) POWERED BY C6.6 Engine
320E RR & 320E LRR Excavators LHN00001-UP (MACHINE) POWERED BY C6.6 Engine


Parts guard Caterpillar catalog:

1348875 GUARD GP-SWIVEL
315B L, 315C, 315D L, 316E L, 317B LN, 318B, 318C, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LR...
3506886 GUARD GP-FAN
320E, 320E L, 320E LN, 323E L
3421832 GUARD GP-CYLINDER
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L
2402988 GUARD AS-TRACK GUIDE
311C, 314E CR, 315, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR,...
2198468 GUARD AS-TRACK GUIDE
315B L, 315D L, 317B LN, 318B, 318C, 318E L, 320B, 320C, 320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 323D LN
2198469 GUARD AS-TRACK GUIDE
315C, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C, 321D LCR, 323D L, ...
1048903 GUARD
307B, 307C, 308C, 311D LRR, 311F LRR, 312E, 312E L, 313B, 314D CR, 314D LCR, 315D L, 318C, 318D2 L, 319D L, 319D LN, 320D, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LC...
3361161 GUARD AS
312D, 312D L, 312E, 312E L, 315D L, 316E L, 318B, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D LN, 323D SA, 323E L, 324D L, 324E, 324E L, 32...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.