AVSPARE.COM
parts catalog

GUARD AS 9V9810 - Caterpillar



9V9810 GUARD AS Caterpillar parts 916 GUARD
Rating:
13
Alternative (cross code) number:
CA9V9810
9V-9810
9V9810
Caterpillar 9V9810 GUARD AS
Weight: 0.68 pounds 0 kg.

Buy GUARD AS 9V9810 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 9V9810:

WHEEL LOADER  916   Caterpillar
Number on catalog scheme: 10
 
  For full view, you need register

Information:


Illustration 1.
Front Suspension Frame Group Components. (1) Axle Housing. (2) 3.0 mm (.12 in) Shims. (3) 1.0 mm (.04 in) Shims. (4) Cap. (5) Seal.The differential input shaft the for front axle (1) must be aligned with the transfer gearbox output shaft. The adjustment is done using shims (2 and 3) installed under the bearing caps (4). The objective of the adjustment procedure that follows is to achieve adequate shaft alignment while making sure there is minimum sideways movement of the suspension frame group. There should also be no side load imposed on the bearings.
1. Raise the front of the machine by the mainframe until the tires are off the ground. Place suitable supports under the mainframe.2. Remove the front wheels to improve access to the front suspension frame group.3. With the suspension frame group in position and the suspension arm bearings in place, use a suitable pry bar to move the suspension frame group right and left as needed until the universal joints are aligned. Use a straight edge to measure across the driveshaft universal joints for correct alignment. Take two measurements 180° apart.4. Use a soft mallet to impact both the right and left side bearings to make sure they are fully seated.
Location of Dimension (A) and Dimension (B). 5. Use finger pressure to press on the bearing to remove any seal deflection that may be present. Use a vernier scale, or similar tool, to obtain Dimension A and Dimension B by measuring the distance from the bottom of the counterbore to the top face of the bearing outer shells on the right and left side of the machine. Add Dimensions A and B together.6. For D20D, D250D, D250E and D300E Articulated Trucks, use 3.0 mm (.12 in) thick, 7U-6608 Shims (2) and 1.0 mm (.04 in) thick 6U-1345 Shims (3) to make a shim pack that exceeds the sum of Dimensions A and B by the minimum amount possible. For D25D, D30D, D350D, D40D, D400D, D350E and D400E Articulated Trucks, use 3.0 mm (.12 in) thick, 4U-8849 Shims (2) and 1.0 mm (.04 in) thick 4U-8769 Shims (3) to make a shim pack that exceeds the sum of Dimensions A and B by the minimum amount possible.
7. Divide the shim pack in the best proportions with respect to Dimensions A and B to maintain drive shaft alignment. 8. Install the shim pack and install cap (4). Install the bolts and washers that hold cap (4) in position.9. Measure the total amount of sideways movement of the suspension frame group by using the prybar to move it fully left then fully right. Total side movement should not exceed 1.0 mm (.04 in).10. Check universal joint alignment. Maximum allowable misalignment is 5.0 mm (.20 in). but actual misalignment when using this procedure should be less.Example
1. Measure and record Dimension (A). Dimension (A) is 6.3 mm (.25 in).2. Measure and record Dimension (B). Dimension (B) is 4.1 mm (.16 in).3. Add Dimension (A) 6.3 mm (.25 in) to

Caterpillar parts catalog:

Caterpillar parts catalog
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE


Parts guard Caterpillar catalog:

7V0579 GUARD
916, 926, IT18B, IT28, IT28B
7V0578 GUARD
916, 926, IT18B, IT28, IT28B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.