AVSPARE.COM
parts catalog

GUIDE POST 1C4155 - Caterpillar



1C4155 GUIDE POST Caterpillar parts AP-1200 GUIDE
Rating:
16
Alternative (cross code) number:
CA1C4155
1C-4155
1C4155
Caterpillar 1C4155 GUIDE POST
Weight: 20 pounds 9 kg.

Buy GUIDE POST 1C4155 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT PAVER,

Compatible equipment models: 1C4155:

ASPHALT PAVER  AP-1200   Caterpillar
Number on catalog scheme: 12
 
  For full view, you need register

Information:


Unexpected machine movement can cause injury or death.To avoid possible machine movement, move the hydraulic lockout control to the locked position and attach a Special Instruction, SEHS7332, "Do Not Operate" or similar warning tag to the hydraulic lockout control.
Improperly adjusted bucket clearance could cause galling on the contact surfaces of the bucket and stick, resulting in excessive noise and/or damaged O-ring seals.
Illustration 1 g06185692
Area for linkage adjustment
Illustration 2 g06185866
(1) Pin
(2) Shims
(3) Flange
(4) Stick boss
(5) No gap
(6) Bucket boss
(7) Bucket clearance
(8) Location
(9) Bolts
(10) Washers
(11) PlateThe clearance of the bucket control linkage on this machine can be adjusted by shimming. If the gap between the bucket and the stick becomes excessive, adjust bucket clearance (7) to 0.5 to 1 mm (0.02 to 0.04 inch).Two shims of different thickness are used at location (8). The thicknesses of the shims are 0.5 mm (0.02 inch) and 1.0 mm (0.04 inch).
Position the machine on a level surface and lower the bucket to the ground.
Slowly operate the swing control lever until stick boss (4) and the bucket boss (6) are in full face contact at no gap (5). This will help to determine the total clearance of the connection point of the stick and of the bucket.
Move the hydraulic lockout control to the LOCKED position. Stop the engine.
Measure bucket clearance (7), which is the existing total clearance.
Determine the number of shims that need to be removed from shims (2) by using the following calculation:Subtract 0.5 mm (0.02 inch) or 1.0 mm (0.04 inch) from bucket clearance (7).
Remove the appropriate number of shims at location (8) to meet the above thickness. Make sure that you use a minimum of three 0.5 mm (0.02 inch) shims. To remove the shims, remove bolts (9), washers (10), and plate (11).
After the correct number of shims has been removed and pin (1) is aligned with the pin hole, install plate (11), bolts (9), and washers (10). Tighten the bolts to 240 40 N m (175 30 lb ft).
After installation, make sure that bucket clearance (7) is still correct.

Caterpillar parts catalog:

Caterpillar parts catalog
AP-1200 ASPHALT PAVER 2JD00001-UP (MACHINE) POWERED BY 6.354 ENGINE


Parts guide Caterpillar catalog:

7X9337 GUIDE
AP-800, CB-614, CS-551
7X9336 GUIDE
AP-800, CB-614, CS-551
0780645 GUIDE-SPRING
CP-433B, CP-563, CS-431B, CS-551
9N7301 GUIDE
PR-1000, PR-750B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.